© by N&W GLOBAL VENDING S.p.A.
22
03-2012 3775 00
E
xEcutivE
v
ErsioN
For the Executive system, you must choose from among
the following payment systems:
-Standard
-Price holding
-Price holding price display (UKEY)
i
mmEDiatE
cHaNgE
Usually the amount related to a selection is cashed in
after the machine sends the signal “Selection made”.
By enabling this function, which is disabled by default, the
payment signal is sent at the beginning of the dispensing.
Setting this parameter is compulsory.
bDv
The BDV protocol menus allow you to define the follow
-
ing functions.
i
mmEDiatE
cHaNgE
Usually the amount related to a selection is cashed in
after the machine sends the signal “Selection made”.
By enabling this function, which is disabled by default, the
payment signal is sent at the beginning of the dispensing.
Setting this parameter is compulsory.
t
ypE
of
salE
This allows you to set the operating mode for multiple or
single dispensing. With multiple dispensing, the change
is not automatically returned at the end of one dispens-
ing, but it remains available for further dispensing. When
the coins return button is pressed, the remaining credit
will be returned if its value is less than the maximum
change value.
c
HaNgE
rEfusal
This allows the enabling/disabling of the return of the
credit (escrow) if no dispensing was made.
If enabled, this function allows the coins to be returned
even if the first dispensing has not occurred.
But if a dispensing failed for any reason, if requested, the
change will be returned.
m
aximum
crEDit
This function allows you to define the maximum credit for
the introduced coins which is accepted.
m
aximum
cHaNgE
It is possible to set a limit to the total amount of the
change that the coin box will pay when the change re-
turn button is pressed or after a single dispensing.
Any credit exceeding the programmed amount with this
function will be cashed in.
a
ccEptED
coiNs
It is possible to define which coins among those recog
-
nised by the validator shall be accepted.
In relation to the coin/value correspondence, the label on
the coin box shall be checked, which shows the position of
the coins.
r
EfusED
coiNs
This allows you to program the refusal of coins if the
condition “exact amount” is met.
In relation to the coin/value correspondence, the label on
the coin box shall be checked, which shows the position of
the coins.
“E
xact
amouNt
”
valuE
This data defines the combination of empty tubes which
puts the coin box in the condition of “exact amount”. The
possible combinations of empty tubes are shown below.
For simplicity reasons the combination is described with
reference to the tubes A, B and C, where tube A receives the
lower value coins and tube C the higher value coins.
0
=
A or (B and C)
1
=
A and B and C
2
=
only A and B
3
=
A and B and C
4
=
only A
5
=
only A or B (default)
6
=
A or (B and C)
7
=
only A or B (default)
8
=
only A or B (default)
9
=
only B and C
10
=
only B
11
=
only B and C
12
=
only C
D
ispENsiNg
buttoNs
This function allows you to enable or not the buttons on
the coin box for removing the coins from the coin box
tubes.
c.p.c.
pEripHEral
It communicates to the coin box if some peripherals have
been installed or removed from the serial connection
(C.P.C. type peripherals - the default verification unit is
always enabled).
Summary of Contents for Festival
