NXP Semiconductors AFD4400-RDB Quick Start Manual Download | Manualshive

Page: 7 / 15

background image

1. Ensure that the power switch on the chassis is turned off.
2. Install the enhanced small form-factor pluggable (SFP+) optical transceivers as per your application scenario.

NOTE

The FTLF8526P3BNL and FTLX8573D3BTL SFP+ transceivers from Finisar®
are recommended. For more information, see the Airfast Digital AFD4400-RDB
Reference Manual

(document AFD4400-RDBRM).

3. Connect the Ethernet cable from the switch/LAN port to the registered jack (RJ45) ETH1 port on the chassis.
4. Plug the power adapter to the wall outlet.
5. Turn on the power switch to boot the board.

The system auto boots and shows the universal boot loader (U-Boot) console and the following message appears on the
screen:

U-Boot 2013.04.Freescale_D4400_v2.4-00009-g981ca73 (Jan 02 2015 - 21:36:36)

CPU:Freescale D4400 prev-0x5d, srev-0x10 at 614 MHz

Reset cause: 0x40000001

DDR Clock: 491MHz

ARM Clock: 614MHz

VSPA Clock: 614MHz

DRAM: 768 MB

Board: D4400-RDB, Rev C

VID: 00 -> 1.0500 Volts

Flash: 256 MB

In: serial

Out: serial

Err: serial

Net: SGMII: eTSEC1 [PRIME], eTSEC2

Hit any key to stop autoboot: 5 4 0

D4400-RDB U-Boot =>

D4400-RDB U-Boot =>

7 Re-programming NOR flash

To re-program the NOR flash, follow the steps listed below:

1. Prepare the board. For the instructions, see Section 6, "

Preparing and starting up board

".

2. Configure and test the trivial file transfer protocol (TFTP) server using the steps listed below:

a. Ensure that the TFTP server is running.

b. Select the directory where you have saved the BSP release files.

c. Set the

serverip

variable to the server interface internet protocol (IP) address of the TFTP server application

running on the host PC and save the setting as listed below.

D4400-RDB U-Boot => setenv serverip 10.69.12.25

D4400-RDB U-Boot => saveenv

Saving Environment to Flash...

. done

Un-Protected 1 sectors

. done

Un-Protected 1 sectors

Erasing Flash...

. done

Erased 1 sectors

Writing to Flash... done

. done

Protected 1 sectors

. done

Protected 1 sectors

D4400-RDB U-Boot =>

Re-programming NOR flash

AFD4400 Reference Design Board Quick Start, Rev. 0, 07/2015

Freescale Semiconductor, Inc.

7

Downloaded from

Downloaded from

Downloaded from

Downloaded from

Downloaded from

Downloaded from

Downloaded from

«
...
5
6
7
8
9
...
»

Summary of Contents for AFD4400-RDB
















Reviews:

No comments

Related manuals for AFD4400-RDB

SmartSwitch 9000

Brand: Cabletron Systems Pages: 18

Brand: National Instruments Pages: 40

Brand: VIA Technologies Pages: 39

Brand: ADC Pages: 34

Brands by name

0 1 2 3 4 5 6 7 8 9 A B C D E F G H I J K L M N O P Q R S T U V W X Y Z

Popular brands

Load more brands