background image

10

 

Quick Start Guide

This device complies with Part 15 of the FCC Rules. Operation is subject to the 
following two conditions: 
(1) This device may not cause harmful interference, and 
(2)  This device must accept any interference received, including interference that may 

cause undesired operation. 

Attention that changes or modification not expressly approved by the party 
responsible for compliance could void the user’s authority to operate the equipment.

Note:

 This product has been tested and found to comply with the limits for a Class 

B digital device, pursuant to Part 15 of the FCC Rules. These limits are designed to 
provide reasonable protection against harmful interference in a residential installation. 
This product generates, uses, and can radiate radio frequency energy and, if not 
installed and used in accordance with the instructions, may cause harmful interference 
to radio communications. However, there is no guarantee that interference will not 
occur in a particular installation. If this product does cause harmful interference to 
radio or television reception, which can be determined by turning the equipment off 
and on, the user is encouraged to try to correct the interference by one or more of the 
following measures: 
—Reorient or relocate the receiving antenna. 
— Increase the separation between the equipment and receiver. 
— Connect the equipment into an outlet on a circuit different from that to which the 

receiver is connected. 

— Consult the dealer or an experienced radio/TV technician for help.
This equipment should be installed and operated with a minimum distance 20cm 
between the radiator and your body.

Summary of Contents for i.MX 8M













Reviews: