background image

Document Number:  AN4536

Rev. 3.0

1/2014

How to Reach Us:

Home Page: 

freescale.com

 

Web Support: 

freescale.com/support

Information in this document is provided solely to enable system and software implementers to use Freescale products. 

There are no express or implied copyright licenses granted hereunder to design or fabricate any integrated circuits based 

on the information in this document.

Freescale reserves the right to make changes without further notice to any products herein. Freescale makes no 

warranty, representation, or guarantee regarding the suitability of its products for any particular purpose, nor does 

Freescale assume any liability arising out of the application or use of any product or circuit, and specifically disclaims any 

and all liability, including without limitation consequential or incidental damages. “Typical” parameters that may be 

provided in Freescale data sheets and/or specifications can and do vary in different applications, and actual performance 

may vary over time. All operating parameters, including “typicals,” must be validated for each customer application by 

customer’s technical experts. Freescale does not convey any license under its patent rights nor the rights of others. 

Freescale sells products pursuant to standard terms and conditions of sale, which can be found at the following address: 

freescale.com/SalesTermsandConditions

.

Freescale and the Freescale logo are trademarks of Freescale Semiconductor, Inc., Reg. U.S. Pat. & Tm. Off. 

SMARTMOS is a trademark of Freescale Semiconductor, Inc. All other product or service names are the property of their 

respective owners. 

© 2014 Freescale Semiconductor, Inc.

Summary of Contents for MMPF0100





































Reviews: