background image

6

The  FR7-420  (Sirius7)  is  a  seven-cylinder  radial 
overhead-valve  four-stroke-cycle  engine  of  70cc 
displacement.  The  engine  maintains  the  same 
features of stress free starting, super smooth idling 
and high torque power which is always the hallmark 
of  O.S.  large  size  multi-cylinder  engines.  With  its 
finely  detailed  design  and  outstanding  scale 
appearance  and  sound,  the  engine's  quality  is 
second to none.

ABOUT THE ENGINE

STANDARD ACCESSORIES

Glow Plug Type F (installed on the engine)

Valve adjusting tool kit

Feeler gauge 0.04mm

Feeler gauge 0.1mm
Hex. key 1.5mm
Wrench 5mm

Plug Cable Set

Plug Cable
Plug Terminal (7pcs.)

(7pcs.)

(w/silicone tube)

Radial Mount Retaining Screw Set
    Engine mounting screws (M5X25)
    Lock washers (ø5)
    Blind nuts (M5)

(5pcs.)

(5pcs.)

(5pcs.)

Lead for ground    5 (1pc.)

Needle-Valve Extension Cable Set

STANDARD ACCESSORIES

Drain Plug

Carburetor Insert

Decal

Instruction Manual

Aluminum Case

7

ENGINE PARTS NAME

Lock Nut

Propeller Washer

Crankcase

Propeller Nut

No.1 Cylinder

No.2 Cylinder

No.3 Cylinder

No.4 Cylinder

Front Housing

No.5 Cylinder

No.7 Cylinder

No.6 Cylinder

Summary of Contents for FR7-420



















Reviews: