background image

Glowplug life

Particularly in the case of very high performance 
engines, glowplugs must be regarded as expendable 

Install a plug suitable for the engine.

Use fuel containing a moderate percentage of 
nitromethane unless more is essential for racing 
events.

Do not run the engine too lean and do not leave the 
battery connected while adjusting the needle. 

However, plug life can be extended and engine 
performance maintained by careful use, i.e.:


GLOWPLUG

The role of the glowplug

With a glowplug engine, ignition is initiated by the 
application of a 1.5-volt power source. When the 
battery is disconnected, the heat retained within the 
combustion chamber remains sufficient to keep the 
plug filament glowing, thereby continuing to keep the 
engine running. Ignition timing is 'automatic' : under 
reduced load, allowing higher rpm, the plug becomes 
hotter and, appropriately, fires the fuel/air charge 
earlier; conversely, at reduced rpm, the plug become 
cooler and ignition is retarded.

Since the compatibility of glowplug and fuel may have 
a marked effect on performance and reliability, it may 
be worthwhile to choose the R/C type plug found 
most suitable after tests.Recommended O.S. plugs 
are No.8, A5 and A3. Carefully fit plug finger-tight, 
before final tightening with the correct size plug 
wrench.

The starter prevents the engine from being 
rotated in the wrong direction.The unit will 
be damaged if you attempt to force the fly-
wheel in the opposite direction (i.e. clock-
wise when viewed from the crankshaft end).

NOTE: 
Because, in the interests of personal safety, 
dismantling of the starter mechanism is 
strongly discouraged, the Recoil Starter is 
available for replacement only as a pre-
assembled unit. 
However, some related parts, such as 
Starting Shaft and Rear Adaptor, are 
obtainable separately. (See Parts List.)

11

Summary of Contents for MAX-12CV-R



































Reviews: