background image

It is of vital importance, before attempting to 
operate your engine, to read the general 
'SAFETY INSTRUCTIONS AND WARNINGS' 
section on pages 2-5 of this booklet and to strictly 
adhere to the advice contained therein.

Also, please study the entire contents of this 
instruction manual, so as to familiarize yourself 
with the controls and other features of the 
engine.

Keep these instructions in a safe place so that 
you may readily refer to them whenever 
necessary.

It is suggested that any instructions supplied 
with the vehicle, radio control equipment, etc., 
are accessible for checking at the same time.

1

CONTENTS

18

SAFETY INSTRUCTIONS AND 

WARNINGS ABOUT YOUR O.S. ENGINE

15CV-R SERIES INTRODUCTION

BASIC ENGINE PARTS

INSTALLATION 

SUPER AIR CLEANER

NOTES CONCERNING 

THE RECOIL STARTER

GLOWPLUG

TOOLS, ACCESSORIES, etc. 

CARBURETOR CONTROLS

PRESSURIZED FUEL SYSTEM

2-5

6

8-9

11-12

12-13

15

16-17

32-33

STARTING THE ENGINE &

RUNNING-IN('Breaking-in)

IF THE ENGINE FAILS TO START 

FINAL ADJUSTMENT

CARBURETOR CLEANLINESS

CARE AND MAINTENANCE

O.S. GENUINE PARTS & ACCESSORIES

ENGINES EXPLODED VIEW &

PARTS LIST

CARBURETOR EXPLODED VIEW  & 

PARTS LIST

THREE VIEW DRAWING

22-23

7

9-11

13-14

14-15

24-31

18-19

20

21

34-36

Summary of Contents for MAX-15CV-R Series




















Reviews: