background image

4

NOTES

These  engine  were  designed  for  model 
helicopters.  Do  not  attempt  to  use  it  for  any 
other purpose.

Mount the engine in your model securely, fol-
lowing the manufacturers' recommendations, 
using appropriate screws and locknuts.

Install an effective silencer (muffler). Frequent 
close exposure to a noisy exhaust (especially 
in  the  case  of  the  more  powerful  high-speed 
engines)  may  eventually  impair  your  hearing 
and  such  noise  is  also  likely  to  cause 
annoyance to others over a wide area.

Check  the  linkage  to  the  throttle  arm  before 
each flight.

Avoid sudden high r.p.m. immediately after the 
engine is started, as the clutch will engage and 
you may be struck by the rotor.

After starting the engine, carry out any needle-
valve readjustments after stopping the rotor by 
closing the throttle to the lowest r.p.m.. 
Stop  the  engine  before  attempting  to  make 
other adjustments to the carburetor.

Use  an  electric  starter.  The  wearing  of  safety 
glasses is also strongly recommended. 
Press the rotor head down securely.

Take  care  that  the  glow  plug  clip  or  battery 
leads  do  not  come  into  contact  with  rotating 
parts.

Adjust  the  throttle  linkage  so  that  the  engine 
stops when the throttle stick and trim lever on 
the transmitter are fully retarded. Alternatively, 
the  engine  may  be  stopped  by  cutting  off  the 
fuel  supply.  Never  try  to  stop  the  engine 
physically.

5

NOTES

Take care that loose clothing (ties, shirt sleeves, 
scarves etc.) do not come into contact with the 
rotor. Do not carry loose objects (such as pen-
cils, screwdrivers, etc.) in a shirt pocket from 
where they could fall through the rotor disc.

For their safety, keep all onlookers (especially 
small children) well back (at least 20 feet or 6 
meters) when preparing your model for flight. If 
you have to carry the model to the take-off point 
with the engine running, be especially cautious. 
Hold the rotor securely and keep well clear of 
spectators.

Warning! lmmediately after a glowplug-ignition 
engine  has  been  run  and  is  still  warm, 
conditions  sometimes  exist  whereby  it  is  just 
possible  for  the  engine  to  restart  when  turned 
over  WITHOUT  the  glowplug  battery  being 
reconnected.  Remember  this  if  you  wish  to 
avoid the risk of accidents.

Summary of Contents for MAX-91SX-HRING C Spec PS VIPER






















Reviews: