background image

16

BEFORE STARTING

Tools, accessories, etc.

The  following  items  are  necessary  for  operating  the 
engine.

1  Fuel

Select,  by  practical  tests,  the  most  suitable  fuel  from 
among the best quality fuels available in your country 
for  helicopter  use.  For  the  best  throttle  response,  a 
fuel  containing  10%  to  30%  nitromethane  is 
preferable.  Lubricants  may  be  either  castor-oil  or  a 
suitable  synthetic  oil  (or  .  a  blend  of  both)  provided 
that  they  are  always  of  top  quality.  For  consistent 
performance and long engine life, it is essential to use 
fuel  containing  AT  LEAST  18%  lubricant  by  volume. 
Some  fuels  containing  coloring  additives  tend  to 
deterriorate  and  may  adversely  affect  running 
qualities.  If  in  doubt  compare  to  a  fuel  known  to  be 
good.

Model engine fuel is poisonous. Do not allow 
it  to  come  into  contact  with  the  eyes  or 
mouth. Always store it in a clearly marked 
container and out of the reach of children.

Reminder!

The pump requires running-in as with the engine. Be 
sure  to  check  the  silicone  tubes  and  connections 
carefully  for  any  cracks  on  the  tubes  and  loose 
connections as the engine runs ejecting excess fuel.

17

4  Glowplug battery

The  power  source  for  heating  the  glowplug  may  be 
either a large heavy-duty 1.5volt dry cell, Ni-cd battery 
or battery integrated booster.

1.5 volt dry cell

2  Glowplug

O.S. No.8 glowplug is installed in the engine.

3  Battery leads

These are used to conduct current 
from  the  battery  to  the  glowplug. 
Basically, two leads, with clips,  are 
required,  but,  for  greater  conve-
nience,  twin  leads  with  special 
glowplug connectors, as shown on 
the right, are commercially available.

Model engine fuel is also highly flammable. 
Keep it away from open flame, excessive 
heat, sources of sparks, or anything else 
which might ignite it. Do not smoke, or allow 
anyone else to smoke, near to it.

Battery Integrated booster

Battery leads

Make  sure  glowplug  element 
glows  bright  red  inside  room 
or shadow.

Battery leads

12V Battery

Starter

6 Electric starter and starter
     battery                                 

An  electric  starter  is  recom-
mended for starting.

5 Hexagon starting shaft

This  shaft  mounted  on  an 
electric starting motor is driven 
into  the  shaft  cup  to  turn  the 
engine.

In case of 1.5volt dry cell

Summary of Contents for MAX-91SX-HRING C Spec PS VIPER






















Reviews: