background image

10

GLOWPLUG IGNITER
Commercialy  available  handy 
glowplug  heater  in  which  the 
glowplug  battery  and  battery 
leads are integrated. 

FUEL

Generally, it is suggested that the user selects a fuel 

that is commercially available for model two-stroke 

engines  and  contains  10-30%  nitromethane.  As  a 

starting point, we recommend a fuel containing 20% 

nitromethane,  changing  to  a  fuel  containing  more 

nitro if necessary. When the brand of fuel is changed, 

or  the  nitro  content  increased,  it  is  advisable  to 

repeat  the  running-in  procedure  referred  to  in  the 

RUNNING-IN  paragraphs.  Please  note  that  with 

high-nitro fuels, although power may 

be increased for competition purposes, 

glowplug elements do not last as long 

and engine life will be shortened.  

Items necessary for starting

!  

REMINDER!

Model  engine  fuel  is  poisonous.  Do  not 
allow  it  to  come  into  contact  with  the 
eyes  or  mouth.  Always  store  it  in  a 
clearly  marked  container  and  out  of  the 
reach of children.

TOOLS, ACCESSORIES, etc.

The following items are necessary for operating the engine.

!  

Model  engine  fuel  is  also  highly 
flammable.  Keep  it  away  from  open 
flame, excessive heat, sources of sparks, 
or anything else which might ignite it. Do 
not  smoke  or  allow  anyone  else  to 
smoke, near to it. 

FUEL FILTER

To  be  installed  in  the  fuel  line 
between fuel tank and carburetor 
to  prevent  foreign  matter  from 
entering the carburetor.

STARTER BOX

For starting the engine.

11

FUEL PUMP
For  filling  the  fuel  tank,  a  simple, 
polyethylene  "squeeze"  bottle, 
with a suitable spout, is required. 

SILICONE FUEL LINE

Heatproof  silicone  tubing  of 
approx. 5mm o.d. and 2mm i.d. is 
required  for  the  connection 
between the fuel tank and engine.

TOOLS

HEX SCREWDRIVER

SCREWDRIVER

Necessary for engine installation.
1.5mm, 2mm, 2.5mm, 3mm

Necessary for carburetor adjustments.
No.1, No.2, etc

LONG SOCKET WRENCH WITH PLUG GRIP

Recommended  for  easy  removal  and 
replacement of the angled and recessed 
glowplug, the O.S.Long Socket Wrench 
incorporates a special grip.

BATTERIES FOR STARTER BOX

Batteries  for  starter  box.Select 
according  to  the  starter  box 
used.    Be  sure  to  fully  charge 
before using.

Summary of Contents for 12xz Spec II





















Reviews: