- EN -
20
biOrb HALO
N O T E
•
Do not use aquarium gravel as it could clog the filter
cartridge.
•
Only use the ceramic substrate provided.
•
Do not tip the ceramic substrate into the aquarium
from a height as it could scratch the acrylic.
•
Only use ceramic substrate particles that are at least
pea-sized. Remove and dispose of any particles that
are smaller.
How to proceed:
C
•
Wash and then place the supplied ceramic substrate
carefully into the aquarium and arrange it around
the filter housing.
Installing and connecting the aerator pump
N O T E
When installing the unit, ensure that it
•
is located outside the aquarium
•
is not placed on or over the aquarium
•
cannot fall into the water or move out of position.
Damage resulting from incorrect installation is not ba-
sis for a claim within the framework of the guarantee
or warranty.
How to proceed:
D
1.
Connect the air hose leading out of the aquarium to
the air connection of the aerator pump and fit the
aerator pump above the subsequent level of the
aquarium water. This prevents water from leaking
or damage to the pump in case the integrated non-
return valve should fail.
2.
Connect the connection cable to the separate
socket of the plug-in transformer but do not yet
connect the plug-in transformer to the mains
socket. First complete the start-up prepara-
tions.(→
Connecting the lighting unit
N O T E
Never immerse the lighting units in water or other liq-
uids.
How to proceed:
E
1.
Connect the connection cable to the separate
socket of the plug-in transformer but do not yet
connect the plug-in transformer to the mains
socket. First complete the start-up prepara-
tions.(→
COMMISSIONING/START-UP
Filling with and preparing the water
It is necessary to prepare the aquarium water by add-
ing "Water Conditioner" and "Biological Booster".
How to proceed:
F
1.
Fill the aquarium with tap water up to about 5 cm
below the cover.
2.
Cut open the “Water Conditioner“ bag and pour the
contents into the water.
3.
Switch on the aerator pump; after the pump has
been running for at least 24 h, sprinkle the contents
of the “Biological Booster“ bag into the water.
(→
Switching ON/OFF
C A U T I O N
Strong LED radiation!
Possible consequences: Eye injury due to light flash.
•
Never look into the light source.
N O T E
Never operate an air connection by itself, i. e. without
the tube and aerator connected.
How to proceed:
G
1.
Switching on
: Insert the plug-in transformer into
the socket.
–
Check that the cables form drip loops.
–
The aerator pump will switch on immediately.
2.
Additionally actuate the ON/OFF switch of the light-
ing unit to switch it on.
3.
Switching off
: Disconnect the plug-in transformer.
OPERATION
How to proceed:
•
Switch on the lighting unit with the ON/OFF switch.
Programming the biOrb MCR LED
•
Pull out the small plastic strip before using the re-
mote control for the first time.
•
Switch on the lighting unit with the ON/OFF switch.
Summary of Contents for biOrb HALO Series
