- EN -
11
Accessories
•
EAC Aquarium Controller (33885) for controlling up
to five EAC-compatible devices using the app.
•
Swing adapter (33917) for fastening the LED lamp
on open aquariums.
•
Cable suspension set (33918) for fastening the LED
lamp on the ceiling.
•
EAC transformer (INT 33888, GB 33889) for the
power supply.
•
EAC Y adapter (33897) for operating multiple LED
lamps.
•
Power adapter (33898) for integration of an addi-
tional EAC transformer.
•
IR Control Set (33886) as remote control of up to
two EAC-compatible LED lamps.
Intended use
Exclusively use the HighLine Premium LED as follows:
•
For illumination and facilitating biological processes
in aquariums.
•
Operate in accordance with instructions.
(→
The following restrictions apply to the unit:
•
Only use indoors and for aquaristic purposes in the
home (not for commercial use).
•
Only suitable for freshwater aquariums.
INSTALLATION
Installing the LED lamp with a universal adapter
How to proceed:
B
1.
Undo the fastening screws on both sides. Push the
universal adapter to the desired length and tighten
the fastening screws.
2.
Place the LED lamp on the side of the aquarium.
Installing the LED lamp with a swing adapter
The optionally available swing adapter (33917) is re-
quired for installation on an open aquarium (aquarium
without a lid).
How to proceed:
C
1.
Undo the fastening screws on both sides. Pull out
both universal adapters.
2.
Unscrew the holding fixture of the universal adapter
and fasten it on the swing adapter.
3.
Plug in the swing adapter, push it to the desired
length and tighten the fastening screws.
4.
Place the LED lamp on the side of the aquarium.
Installing the LED lamp with the cable suspension set
The optionally available cable suspension set (33918)
is required for installing the LED lamp on the ceiling.
C A U T I O N
Risk of injury caused by falling lamp.
•
Use suitable dowels and screw hooks for installation
on the ceiling. The dowels and screw hooks in the
cable suspension set are not suitable for all sub-
strates.
How to proceed:
D
1.
Undo the fastening screws on both sides. Push the
universal adapter to the desired length and tighten
the fastening screws.
2.
Install the screw hooks.
–
Spacing between the bores equals the set spread
of the LED lamp with the universal adapter.
3.
Suspend the wire cable with the canopy on the
screw hook. Fasten the canopy in place.
4.
Fit wire cable holder.
a: Undo the knurled nut.
b: Insert wire cable, if there is resistance push with
force, until the wire cable emerges. Set the wire
cable to the desired length.
c: Push down the knurled nut to pull back the wire
cable.
d: Tighten the knurled nut to fasten the wire cable
in place.
5.
Unscrew the threaded pin, insert the short wire ca-
ble in the centre of the slot in the wire cable holder,
screw in and tighten the threaded pin
–
Ensure that both ends of the wire cable are the
same length.
6.
Ensure that the sealed ends of the short wire cables
are attached to the universal adapter.
7.
If required, re-adjust all wire cables, so that the LED
lamp is straight when suspended. Then cut off the
length of wire cable protruding from the wire cable
holder.
Summary of Contents for HighLine Premium LED 100
