21
- GB -
3 Safety
information
Hazards to persons and assets may emanate from this unit if it is used in an improper manner or not in
accordance with its intended use, or if the safety instructions are ignored.
This unit can be used by children from the age of 8 and by persons with physical,
sensory or mental impairments or lack of experience and knowledge, as long as they
are supervised or instructed on how to use the unit safely and are able to understand
the potential hazards. Do not allow children to play with the unit. Do not allow children
to clean or maintain the unit without close supervision.
4 Installation
►
The following tools are required:
−
10 mm ring spanner
−
7 mm socket spanner
−
PZ3 Phillips screwdriver
−
Cordless drill/screwdriver with PZ3 bit (do not set to "drill"!)
4.1 Preparing
the
unit
connection
Before installing, connecting and starting up the unit, perform the following tasks:
−
1 Fit 1× DN 75 slide valve (
A 9)
−
2 Fit 2×
∅
180 mm inlets (
A 4)
−
2 Fit 2× DN 150 outlets (
A 7)
−
2 Fit 2× meshed tubes (
A 6)
►
Remove the container cover.
Fitting the DN 75 slide valve
5.
How to proceed:
B
1. Fit the slide valve into the connecting sleeve and secure with a hose clip.
2. Fit the connecting sleeve onto the connection.
3. Secure the holding plate of the slide valve to the outside of the container with cap nuts.
4. Secure the hose clip on the connection.
Fitting the
∅
180 mm inlet
5.
How to proceed:
C
1. If not already done: Fit the sealing ring into the wall of the container from the outside.
−
Ensure that the raised marking is at the top and aligned in relation to the hole pattern.
2. Fit the inlet to the sealing ring.
−
Ensure that the raised marking is at the top and aligned in relation to the hole pattern.
3. Fasten the sealing ring and inlet from the inside with oval head screws.
−
Tighten all screws diagonally using the cordless screwdriver to ensure that the sealing ring is
uniformly applied. Further tighten the screws using a Phillips screwdriver.
4. Fit the rubber sleeve over the inlet and fasten with a hose clip.
−
Turn the hose clip so that the screw is accessible from the side. This facilitates later installation
work.
18172-07-13_GA_ProfiClear Premiu21 21
25.07.2013 12:58:54
Summary of Contents for ProfiClear Premium
