Troubleshooting guide
Problem
Cause
Solution
Button
lit
+
Solid green indicator light
+ Button
flashing
+ Button
flashing
• Switching on
the appliance
or starting an
automatic cooking
cycle with food
between plates
and without
preheating(manual
mode is
automatically
activated).
• 2 possible options:
–
Choose the temperature
setting by pressing the
button and then press
OK
.
Allow to cook, but you must
monitor the cooking (manual
mode).
–
stop the appliance, remove
the food, close the appliance
properly, re-program the
appliance and wait until end
of preheating.
The appliance stops during the
cycle of pre-heating or cooking.
• The appliance has
been kept open
for too long while
cooking.
• The appliance has
been idle too long
after the end of
warm up or keep
warm.
• Disconnect the appliance from
the outlet and leave for 2-3
mins., restart the process. The
next time you use the appliance,
make sure you open and
close it quick for best cooking
results. If the problem occurs
again contact your local Tefal
customer service.
Flashing white indicator light.
+ /
/
/
button
flashing
+ Dis continue bip
• Appliance failure.
• Appliance stored or
used in a room that
is too cold.
• Disconnect and reconnect your
appliance and immediately
restart a preheat cycle. If the
problem persists, contact your
Customer Service.
The appliance no longer beeps.
After the preheating, I have put
my food on the grill but the
indicator stays on PURPLE
and the cooking cycle does not
start.
• Your food is thicker
than 4 cm.
• Food must not be thicker than
4 cm.
• You have not
completely opened
the grill to place
the food.
• Completely open the grill then
close it.
• Not sensing the
food.
The food
thickness too
thin, "OK" is
flashing.
• Confirm the start of the cooking
by pressing the button.
The appliance will activate in
manual mode
+
The indicator light
will blink
red.
• Preheating time
was cut short.
• Monitor the cooking periodically
(for use in manual mode).
Or
• Stop the grill, remove food,
close the grill, select the new
cooking programme you wish to
use and wait for the preheating
cycle to finish.
Flashing white
+ button
flashing
+ Continuous bip
• Appliance failure
• Unplug the product and contact
your customer service.
94
95
optigrillplusxl_ul_0316.indd 94
2016-03-16 15:56:17
Summary of Contents for GO722DS0
