Copyright 2010-2017 Obihai Technology, Inc.
159
Note: $state is alias of $sys.auPath
bt
Bluetooth connection status if Bluetooth is enabled
on the phone
Connected To
(note: includes 1 white space at the end)
= Connected
to a Bluetooh device
Trying To Connect With
(note: includes 1 white space at the end)
=
Trying to connect to a Bluetooth device
Disconnected
= Not connected to any device
No Home/Roam Network Available
= Bluetooth offline
Note:
-
$state is alias of $bt.status
-
$bt.hsp is the pairing mode:
o
Enabled
= Pair with headset
o
Disabled
= Pair with mobile phone
cfa
Call forward unconditional service on/off status
Enabled
= feature is enabled
Disabled
= feature is disabled
dnd
Do Not Disturb setting on/off status
Enabled
= feature is enabled
Disabled
= feature is disabled
dnr
Do Not Ring setting on/off status
Enabled
= feature is enabled
Disabled
= feature is disabled
mwi
Mailbox Status
0
= no new messages in mailbox
n
(where
n
> 0) = New messages in mailbox
net
Ethernet Status: Shows an icon to indicate if Ethernet
is not connected properly
0
= Ethernet down (no link or no IP address)
n
(where
n
> 0) = Ethernet is up
rpd
Repeat Dialing status: Shows an icon to indicate if
(auto) repeat dialing is in progress
0
: Repeat dialing is not not active
1
: Repeat dialing is active
dialxfer
Dialing a number to transfer: Shows an icon to
indicate dialing a transfer target number
0
= not dialing a blind transfer target
1
= dialing a blind transfer target
Note:
-
$state is alias of $dial.bxfer
-
$dial.divert =
1
when dialing a diversion target number
-
$dial.xfer =
1
when dialing a transfer target number
-
$dial.conf =
1
when dialing a conference target number
-
At most one of $dial.xfer, $dial.bxfer, dial.divert, and
dial.conf can be
1
dialtype
Current dialing type: Shows an icon to indicate if the
user is dialing a special number. For example: dialing
an intercom, dialing a call-forward number, making
an anonymous call, requesting to barge-in the called
party, requesting to whisper (a.k.a. coach) the called
party.
cfwd
= Entering a cal forward number
spd
= Entering a Speed Dial 99 entry
intercom
= Entering a target number to intercom
barge-in
= Entering a target number to barge-in
coach
= Entering a target number to coach (a.k.a. whisper)
pickup
= Enter a target number to pickup (directed call pickup)
bci
= Dialing an anonymous call (block caller ID)
Note: $state is alias of $dial.type
rbt
Reboot Needed status: Shows an icon to indicate if a
reboot is needed to have a recent configuration
change to take effect
0
: Reboot not needed
1
: Reboot needed for some recent changes to take effect
upg
Firmware Update status: Shows an icon that indicates
if firmware update is in progress
0
: software upgrade is not in progress
1
: software upgrade in progress
wifi
WiFi connection status: Shows the signal strength or
connection status if WiFi is enabled
fail
= Not connected to any AP
busy
= Trying to connect to an AP
none
or
empty
= WIFI disable
sec
= Connected to a secured AP
open
= Connected to an open-access (insecure) AP
Note:
-
$state is alias of $wifi.status
-
$wifi.signal is the WIFI signal strength (
0
-
5
)
zt
ZT Customization status: Shows an icon to indicate
the ZT Customization process has not yet completed
on the phone
0
= ZT customization has not been completed
n
(where
n
> 0) = ZT customization has been completed
usbkb
USB Keyboard status: Shows a keyboard icon to
indicate that a USB keyboard is connected to the
phone
0
= no USB keyboard connected
1
= USB keyboard connected
Note:
-
$state is alias ofr $sys.usbkb
-
$sys.usbkbcaps =
1
if keyboard caps-lock is on, or
0
otherwise
