Copyright 2010-2013 Obihai Technology, Inc.
151
<x-line-port-status version="
ver
" state="
full-or-partial
">
<line id="1" state="
line-port-state
"/>"
</x-line-port-status>
Where …
-
ver
is a monotonically increasing integer on each NOTIFY, starting with 0
-
full-or-partial
is either
o
full (for the immediate NOTIFY triggered by a SUBSCRIBE), or
o
partial (for the NOTIFY triggered by a status change on the LINE port)
-
line-port-state
can be one the following values:
o
onhook = LINE port is on hook
o
line in use = The PSTN line is being used by an external handset parallel to the LINE port
o
ringing = The line is ringing
o
offhook = The LINE port is currently off hook
o
pwr down = The PSTN line is disconnected from the LINE port
LINE Port Parameter Guide:
Parameter
Description
Default Setting
LINE Port
Enable
Enable the LINE port
Yes
DigitMap
Digit map to restrict numbers that can be dialed or
called on the PSTN line.
See
OBi Call Routing and Digit Map Section
for a
description of the syntaxes for specifying a Digit
Map.
(xxxxxxxS4|1xxxxxxxxxx|xx.)
InboundCallRoute
Routing rule for directing incoming calls on PSTN
line. The default rule is to send all incoming calls to
the PHONE port (ph).
See
OBi Call Routing and Digit Map Section
for a
description of the syntaxes for specifying this
parameter
ph
RingDelay
Delay in milliseconds after initial ring detected on
the LINE port before the device acts on the call (to
route it according to InboundCallRoute). This value
could be 0 so that the call is handled immediately.
However, you should consider setting it to a large
enough value to allow OBi to completely decode
the PSTN Caller-ID signal if the service is available
on the PSTN line. This is required if the
InboundCallRoute relies on Caller-ID information
to route the incoming call.
5500
RingProfile
Select a Ring Profile to ring the PHONE port with
when an incoming call is routed to the PHONE
port. Choices are A, or B
A
DefaultRing
Default ring pattern number to ring the PHONE
port for incoming calls on this trunk that are
routed to the PHONE port according to the
InboundCallRoute of this service. The ring pattern
is taken from the selected Ring Profile. Valid
choices are 1-10
1
CallOnHoldRing
Pattern to ring PHONE port when holding a call on
this trunk that has been connected to the PHONE
8
Summary of Contents for OBi100
