background image

 

L I M I T E D   W A R R A N T Y  

1.

 

Obsidian Control Systems hereby warrants, to the original purchaser, Obsidian Control Systems products to be 
free of manufacturing defects in material and workmanship for a period of two years (730 days). 

2.

 

For warranty service, send the product only to the Obsidian Control Systems service center. All shipping charges 
must  be  pre-paid.  If  the  requested  repairs  or  service  (including  parts  replacement)  are  within  the  terms  of  this 
warranty, Obsidian Control Systems will pay return shipping charges only to a designated point within the United 
States. If any product is sent, it must be shipped in its original package and packaging material. No accessories 
should be shipped with the product. If any accessories are shipped with the product, Obsidian Control Systems 
shall have no liability whatsoever for loss and/or or damage to any such accessories, nor for the safe return thereof. 

3.

 

This warranty is void if the product serial number and/or labels are altered or removed; if the product is modified 
in any manner which Obsidian Control Systems concludes, after inspection, affects the reliability of the product; 
if the product has been repaired or serviced by anyone other than the Obsidian Control Systems factory unless 
prior  written  authorization  was  issued  to  purchaser  by  Obsidian  Control  Systems;  if  the  product  is  damaged 
because not properly maintained as set forth in the product instructions, guidelines and/or user manual. 

4.

 

This is not a service contract, and this warranty does not include any maintenance, cleaning or periodic check-up. 
During the periods as specified above, Obsidian Control Systems will replace defective parts at its expense, and 
will absorb all expenses for warranty service and repair labor by reason of defects in material or workmanship. The 
sole responsibility of Obsidian Control Systems under this warranty shall be limited to the repair of the product, or 
replacement thereof, including parts, at the sole discretion of Obsidian Control Systems. All products covered by 
this warranty were manufactured after January 1, 1990, and bare identifying marks to that effect.  

5.

 

Obsidian Control Systems reserves the right to make changes in design and/or performance improvements upon 
its products without any obligation to include these changes in any products theretofore manufactured.  

6.

 

No warranty, whether expressed or implied, is given or made with respect to any accessory supplied with the 
products described above. Except to the extent prohibited by applicable law, all implied warranties made by 
Obsidian Control Systems in connection with this product, including warranties of merchantability or fitness, are 
limited in duration to the warranty periods set forth above. And no warranties, whether expressed or implied, 
including warranties of merchantability or fitness, shall apply to this product after said periods have expired. The 
consumer’s and/or dealer’s sole remedy shall be such repair or replacement as is expressly provided above; and 
under  no  circumstances  shall  Obsidian  Control  Systems  be  liable  for  any  loss  and/or  damage,  direct  and/or 
consequential, arising out of the use of, and/or the inability to use, this product.  

7.

 

This warranty is the only written warranty applicable to Obsidian Control Systems products and supersedes all 
prior warranties and written descriptions of warranty terms and conditions heretofore published. 

8.

 

Use of software and firmware: 
To the maximum extent permitted by applicable law, in no event shall Elation or Obsidian Control Systems or its 
suppliers be liable for any damages whatsoever (including, but not limited to, damages for loss of profits or data, 
for business interruption, for personal injury or other loss whatsoever) arising out of or in any way related to the 
use of or inability to use firmware or software, the provision of or failure to provide support or other services, 
information, firmware, software, and related content through the software or otherwise arising out of the use 
of  any software or firmware, even in the event of the fault, tort (including negligence), misrepresentation, strict 
liability, breach of warranty of Elation or Obsidian Control Systems or any supplier, and even if Elation or Obsidian 
Control Systems or any supplier has been advised of the possibility of such damages. 

WARRANTY RETURNS:

 All returned service items, whether under warranty or not, must be freight pre-paid and 

accompany a return authorization (R.A.) number. The R.A. number must be clearly written on the outside of the return 
package. A brief description of the problem as well as the R.A. number must also be written down on a piece of 
paper and included in the shipping container. If the unit is under warranty, you must provide a copy of your proof of 
purchase invoice. Items returned without a R.A. number clearly marked on the outside of the package will be refused 
and returned at customer’s expense. You may obtain a R.A. number by contacting customer support. 

Summary of Contents for Netron RDM10
















Reviews: