background image

ATB1 USER MANUAL

18/07/2022 912S-02692-1.11 

21

4.3  Connecting with WiFi

To connect a mobile device or PC with AIS capable navigation software to the ATB1 via WiFi 

is dependent on the original set-up of the unit.

4.3.1  With the default WiFi settings

Following a successful configuration, if no specific information is entered, the ATB1 will be 

visible with the SSID: OS_AISxxxxxxxx where xxxxxxxx is the serial number.

4.3.2  With Direct Mode set-up

If an SSID and password has been entered and Direct Mode selected via the Web based 

or Mobile App then the ATB1 will be visible to other devices with that SSID. Connect your 

device to the ATB1 using the previously entered password.

Once the device is connected open the third party software application and use the settings 

within that program to connect to 

IP address 192.168.4.1 port 24000

.

When connected GPS information and AIS target information will be available within that 

application.

4.3.3  With Vessel Network Mode set-up

If the unit has been set-up originally in Vessel Network Mode with the SSID and password 

of an on-board network the ATB1 will connect automatically to that network on power up. 

The ATB1 will be allocated an IP address by the network router. Before you can connect 

another device running AIS capable navigation software it will be necessary to access the 

router configuration and determine this IP address. The ATB1 will show in the router as 

“Espressif”. Once the IP address has been determined open the third party software appli-

cation and use the settings within that program to connect to the appropriate IP address 

port 24000.

When connected GPS information and AIS target information will be available within that 

application.

!

 

When restarted it is possible that a router will allocate a different IP ad-

dress. For consistent connections use the router configuration software to 

set a fixed IP address for the ATB1

Summary of Contents for ATB1





























Reviews: