Oceanic OCL, Operating Manual

39

OCL OPERATING MANUAL

© 2002 Design, 2014

Doc. No. 12-5378-r01 (4/9/15)

>> If On is saved and a CDT was set, the CDT will start counting down and operation will revert to the Lead-in.

>> If Off is saved, the Timer will stop counting down and operation will revert to the Lead-in.

>> If Set is saved, the Set CDT screen will be displayed.

•  S (2 sec) - to revert to CDT Lead-in.

Set CDT, 

information includes (Fig. 107):

>  Graphics SEt and CDT

>  CDT (min:sec) with Minute digits flashing 

>  min and sec icons

•  A (hold) - to scroll upward through Minute Set Points at a rate of 8 per second from 0: to 59: in increments of 1: (min). 

•  A (< 2 sec) - to step upward through Set Points one at a time.

•  M (< 2 sec) - to step back through Set Points one at a time.

•  S (< 2 sec) - to save the Minute Set Point and flash the Seconds digits.

•  A (hold) - to scroll upward through Seconds Set Points at a rate of 8 per second from :00 to :59 in increments of :01 

(sec). 

•  A (< 2 sec) - to step upward through Set Points one at a time.

•  M (< 2 sec) - to step back through Set Points one at a time.

•  S (< 2 sec) - to save the CDT min:sec setting and revert to the CDT Status screen with OFF flashing.

--------------------------------------------------------------------------------------------------------------

SET FA (FREE ALARMS) MENU

Sequence >> Lead-in >> EDT >> DA1 >> DA2 >> DA3

Set Points remain as set until changed.

Set FA Lead-in,

 information includes (Fig. 108):

>  Graphics SEt and FA

•  A (< 2 sec) - to step forward to Set M Lead-in.

•  M (< 2 sec) - to step back to CDT Lead-in.

•  S (< 2 sec) - to access Set EDT Alarm.

EDT (ELAPSED DIVE TIME) ALARM

Factory set for a fixed 30 seconds, the EDT alarm sounds the audible every 30 seconds during FREE dives.

Set EDT Alarm, 

information includes (Fig. 109):

>  Graphics SEt and EDT -

>  OFF (or ON) flashing

•  A or M (< 2 sec) - to toggle between ON and OFF.

•  S (< 2 sec) - to save the setting and access Set DA1.

•  S (2 sec) - to step back to Set FA Lead-in.

DA (DEPTH ALARMS)

There are 3 Free Depth Alarms (DAs) that can be set at progressively deeper depths*.  

*The DA2 setting must be deeper than DA1 and DA3 must be deeper than DA2.  

Set DA1 Alarm, 

information includes (Fig. 110A):

>  Graphics SEt and - dA1

>  Graphic OFF, or Depth value with MAX and FT (or M) icons, flashing

•  A (hold) - to scroll upward through settings at a rate of 8 per second from OFF to 30 to 330 FT (10 to 100 M) in 

increments of 10 FT (1 M). 

•  A (< 2 sec) - to step upward through settings one at a time.

•  M (< 2 sec) - to step back through settings one at a time.

•  S (< 2 sec) - to save the setting.

> If OFF is saved, operation reverts to Set FA Lead-in.

> If a Depth value is saved, Set DA 2 is accessed.

•  S (2 sec) - to step back to Set EDT Alarm.

Set DA 2 and DA 3 are similar with Depth values beginning 1 increment higher (deeper) than the previous 
selection set.  Example:  If DA 1 is set for 100 FT, DA 2 settings start at 110 FT.

If DA 1 (or DA 2) is set OFF, a Set DA 1 (or 2) First message will be displayed (Fig. 110B) when attempt is made to access Set 

DA 2 (or 3).

Fig. 107 - SET CDT

Fig. 106B - CDT STATUS

(to access Set)

Fig. 108 - SET FA LEAD-IN

Fig. 109 - SET EDT ALARM

Fig. 110A - SET DA1

Fig. 110B - SET DA1

FIRST MESSAGE