background image

40

PROPLUS X OPERATING MANUAL

© Pelagic, 2016

Doc. No. 12-5655-r01 (8/19/16)

DELAYED VIOLATION 3

If you descend deeper than the maximum functional depth*, the audible alarm will sound. Also, the up arrows, and TOO DEEP message will flash. 

Only dashes will display for Current Depth and NDC (No Decompression) time signifying that you are too deep.

* The maximum functional depth (Dive/Gauge = 330 ft / 100 m) is the depth at which the ProPlus X can properly perform calculations or provide accurate display information.

Upon ascending above the maximum functional depth, current depth will be restored. However, the log for that dive will display dashes for max 

depth.

DELAYED VIOLATION 1

If you remain shallower than a Deco Stop Depth for more than 5 minutes, operation will enter Delayed Violation 1* which is a continuation of 

Conditional Violation with penalty time still being added. Again, the audible alarm will sound and the full Tissue Loading Bar Graph will flash until it 

is silenced.

*The difference is that 5 minutes after surfacing from the dive, operation will now enter Violation Gauge Mode.

•  Down arrow and DOWN TO STOP message continues to flash until descending below the required Stop Depth.

•  If the Delayed Violation 1 status is ignored, the ProPlus X will enter Delayed Violation 1 Surface mode for 5 minutes upon surfacing from the dive.  

Down arrows and Deco Stop depth/time will alternate with VIOLATION. After 5 minutes on the surface in DV1 mode, the unit will enter VGM 

(Violation Gauge Mode).

AR

%

11

GAS 1

 -

AIR

FO2 PO2

-

20

14

FT

100

TL

%

1198

PSI

(v) TO MENU - (>) TO COMPASS

15

15

DECO STOP

GTR

FT

DOWN TO

STOP

DV 1 Dive Main

GAS 1

 -

AIR

FO2 PO2

-

20

100

TL

%

1198

PSI

(v) TO MENU - (>) TO COMPASS

15

15

DECO STOP

FT

GTR

DOWN TO

STOP

0 01

SURF

::

DV 1 < 5 Min On Surface

DELAYED VIOLATION 2

If the calculated Decompression obligation requires a Stop Depth between 60 ft (18 m)  and 70 ft (21 m), operation will enter Delayed Violation 2. 

The audible alarm will sound. Additionally, the full Tissue Loading Bar Graph will flash until the audible is silenced.

• Up arrows flash if 10 ft (3 m) deeper than the required Stop Depth.

•  Once within 10 ft (3 m) of and below the required Stop Depth, the DECO STOP message will be displayed.

AR

%

11

SPG

GAS 1

36%

FO2 PO2

1.40

60

72

FT

100

TL

%

(v) TO MENU - (>) TO COMPASS

2

FT

DECO STOP

DECO

66°

F

12:26

PM

70%

AR

%

11

GAS 1

 -

AIR

FO2 PO2

-

---

FT

54

TL

%

1261

PSI

(v) TO MENU - (>) TO COMPASS

--

37

EDT

21

GTR

DEEP

TOO

NDC

Summary of Contents for PROPLUS X






























































Reviews: