background image

19

If you are located in either North, Central or South America please contact the Warranty Department at: 

OceanLED USA LLC

778 South Military Trail

Deerfield Beach

Florida

FL 33442-3025

United States

Tel:+1(954) 523-2250

Fax:+1(954) 523-2249

Email sales@oceanledusa.com

Or if you are located in any other area please contact the Warranty Department at our UK Head Office at:

Ocean LED Marine LTD

Unit 1 Jacknell Road

Dodwells Bridge Industrial Estate

Hinckley

Leicestershire LE10 3BS

United Kingdom

Tel: +44 1455 637505

Fax: +44 1455 238553

Email sales@oceanled.com

6.4.3 When you contact you will be required to provide the information recorded on the warranty claim information 

sheet and have the copy of your purchase invoice for the products where you believe there is a problem. The 

Service team will review with you your problem and where possible advise on any further checks that may 

be required to be done. If from the test results you do appear to have a problem you will be issued with a 

Warranty Claim number. The Claim number is unique to your claim and should be used in all correspondence 

and attached to the returned parts. 

6.4.4  You will be required to return the faulty part with the attached WC number to the appropriate address in 

section 6.4.2. The return of the part is at your expense.

6.4.5  The part will be investigated and if the cause is established to be a manufacturing error or a problem with the 

components we will return a replacement part to you.

6.4.6  If you require a part urgently from us, you would be required to purchase a new one from us. You then have a 

maximum of 30 days to return the faulty part to us. We will investigate and if the product has a problem due to 

our manufacturing will provide a full refund. If you do not think that you can return the part to us within the 30 

days please contact the Service Manager. If the product is not returned within the time limit the claim will be 

closed and no refund given.

6.4.7  If we are unable to find a problem with the part, we will inform you of the outcome. We can provide guidance 

to possible reasons for the fault. Unfortunately we are not liable for or can fix problems with equipment & 

installations that are not purchased from OceanLED. The returned product can be returned to you at your 

request.

Summary of Contents for X4





















Reviews: