background image

3

IMPORTANT PRECAUTIONS!

ATTENTION INSTALLER

:

 

This manual contains important information about the installation, 

operation and safe use of this product. This information should be given to the owner and/ or operator of 

this equipment.

CAUTION

:

 

Risk Group 2 

Possibly hazardous optical radiation emitted from this product. Do not 

stare at operating lamp. May be harmful to the eye.

CLASS 3

:

 

This equipment is designed to operate at voltages of less than 50v DC.

DANGER!

 

Risk of electrical shock or electrocution!

This underwater light must be installed by a Licensed Marine Electrician in accordance with ABYC 

(American Boat and Yacht Council), NMMA, and any other applicable codes and ordinances. Improper 

installation will create an electrical hazard which could result in death or serious injury to swimmers, 

installers, or others due to electrical shock, and may also cause damage to property. Always disconnect the 

power to the light at the circuit breaker before servicing the light. Failure to do so could result in death or 

serious injury to serviceman, swimmers or others due to electrical shock. 

WARNING:

 

• 

Before installing your OceanLED light, read and follow all warning notices and instructions which are 

included. Failure to follow safety warnings and instructions can result in property damage, severe injury, 

or even death.

• 

Before installing your OceanLED light, check local laws for restrictions regarding the use of coloured 

lights in your area.

• 

Salt is an inherently corrosive material. Metal parts and certain natural and man-made surfaces are 

particularly susceptible to corrosion and deterioration when used in and around salt water. OceanLED 

X Series lights are polymer and are impervious to salt water corrosion. Monitor annually to ensure the 

lights remain in service for years to come along with screws and fasteners used for the installation 

which must be of a marine grade type stainless steel or equivalent.

Not suitable for use as on docks, piers or pilings. 

See our Dock Light products.

Summary of Contents for X4





















Reviews: