background image

Copyright © 2009

ODOG5010Mnl v1.1

WARRANTY & REPAIR SERVICE

O’Donnell will warrant this engine for 90 days after the purchase from 
defects in materials or workmanship. O’Donnell will either repair or 
replace, at no charge, the incorrectly made part. (

Please note:

 O’Donnell 

engines are manufactured to the highest standards using only the very 
best materials. However, since this engine will be used in high level racing 
conditions using high Nitro fuels, wear and tear and/or damage as a result 
will not be covered under this warranty.)

Make sure you save the receipt or invoice you were given when you bought 
your engine! It is your proof of purchase and we must see it before we can 
honor the warranty.

Repair service is available anytime. You can have your engine repaired for a 
small charge by the experts at O’Donnell’s authorized repair facility, Hobby 
Services, at the address listed below. To speed up the repair process, 
please do the following:

1. Under all circumstances, return the entire engine.
2.  Send written instructions that include a thorough explanation 

of the problem, the service needed and your phone number 
during the day. (If you expect the the repair to be covered 
under warranty, be sure to include proof of purchase.

3. Be sure to send your full return address

Hobby Services

3002 N. Apollo Drive, Suite 1

Champaign, Illinois 61822

Attn: Service Department

(217) 398-0007

9:00 am-5:00 pm Central Time M-F

E-mail: hobbyservices@hobbico.com

www.hobbyservices.com

Summary of Contents for SS .21

















Reviews: