Odyssey T.E.D. ODY-1719, User Manual

16

We hope you enjoy your purchase of the 
T.E.D. and that this user manual helps 
you get your drone off the ground and 
taking photos!

Included Contents

1. T.E.D. Unit 2.4 Ghz
2. Rechargeable 3.7v Lithium Battery
3. USB Charging Cable
4. Instruction Manual
5. Quickstart Guide
6. 4x Replacement Blades

Specifications

Charging Time: About 40 minutes 
Flying Time: About 6-7 minutes 
Weight: 1.1 Ounce
Controlling Distance: 
About 20 meters 
Battery for Quadcopter: 
3.7V 200mAh 

Flight Preparation

Arm Folding

Please Note: The T.E.D.’s arms and propel-
lers are folded within the body and you must 
use the bottom button on the underside the 
drone to pop the arms out.
Step 1: Remove your drone from its box and 
turn it over.
Step 2: You will see a small circular shaped 
button. Press this button once, a short press.
Step 3: The arms of the drone will pop out.
Please Note: We suggest when putting the 
drone away to align the propeller blades with 
the arm and gently push each arm into place.

Propeller Installation

Please Note: There are faint letters on the 
underside of the propellers which will help 
you distinguish blade from blade. The top left 

and back right blades are A and match with 
the A blades and the bottom left and top right 
are B and match with the B blades.
Please ensure proper installation of the 
propellers to fly the drone.

Step 1: The drone comes with four replace-
ment propellers which should be used in 
case a propeller is lost or breaks due to an 
accident.
Step 2: Match your propellers to each wing 
by the corresponding letter: A, B, and B, A
Step 3: Place each propeller on the small pin 
on the corresponding wing.

Charging the T.E.D. Battery

Please Note: The T.E.D. comes with a 
partially charged battery, however in the case 
that you need to charge the battery please 
follow the instructions below. You do not need 
to remove the battery from the drone to 
charge it. Charging time may take up to 45 
minutes.

Step 1: Connect the T.E.D. to a 
powered USB port, such as a computer.  
 

Step 2: A red LED light will appear   

on the USB indicating the charge    

has completed. Unplug once completed.

Warning: Please check the batteries 
regularly as potential leakage and/or corro-
sion of old batteries can damage the drone 
and/or create a fire hazard.

Caution:

• Remove the batteries immediately if you 

sense any smell or smoke.

• Do not charge the batteries if they are hot, 

wait until they cool down.

• Do not charge the batteries next to inflam-

mables or on a conductive surface.

• Do not overcharge the battery, once the red 

light disappears, discontent the battery.

• Do not use non-Odyssey batteries and 

battery chargers. Only use those which 
come packaged with this device. If you 
need additional batteries or chargers, they 
are available in our Parts Shop on www.od-
ysseytoys.com.

• For safety and best practice, unplug the 

battery connection from the power source 
inside the drone when not in operation.

Downloading the Application and 

Pairing Your Device to the Drone

Notice: The T.E.D. quadcopter’s transmitter is 
application based; you must download the 
free app to fly the drone. The PANTONMA 
app is supported on Android and iOS 
devices.

Step 1: Use your phone to scan the QR code 
or install the app by accessing the 
Play/iTunes store and searching for 
PANTONMA.
Step 2: Press and hold the power button, on 
the bottom of the drone. The drone will turn 
on and the lights will flash.
Step 3: Connect your phone to the drone’s 
Wi-Fi signal named KD****.
Step 4: Open the PANTOMMA app and tap 
My Drone. This will connect your drone to the 
application.

Let’s Fly - Flying T.E.D.

Menu Buttons

Photo: Use the camera on your drone to 
take a photo.
Video: Use the camera on your drone to 
record a video.
Gravity Sensor: Fly the drone by using the 
phone’s movements as the controller.
Hide/Show Display: Show or hide the 
throttle and Directional Sticks from your 
screen. 
Speed: Change your speed from 30%, and 
100%
Auto Back: Drone stabilizes and returns 
home.
SmartFLY Tech: Drone responds to the 
directions as if it is facing the way you’re 
facing.

Light: Turn light on/off on the drone
3D VR: Allows you to watch your videos in 
virtual headset mode (not included).
Back: Return to the previous Menu
Right Stick: Moves the drone side to side 
and forward and backwards.
Forward/Back Trim: Tap to center the drone 
if drifting forward or backward.
Side-To-Side Trim: Tap to center the drone if 
drifting to the left or right.
Media: Access your photos and videos and 
view them.
Auto Trim Reset: Tap to reset the trim. In 
most cases this will take care of drifting 
without using the manual trim controls.
Auto Take Off/Auto Landing: Accelerate 
immediately Auto Landing: Descend immedi-
ately. Emergency Stop: Press and hold for 3 
seconds for an immediate, emergency stop.

Left/Right Hand Switch: Switch the left and 
right joysticks, great for lefties.
Turning Trim: Tap to center the drone if 
drifting in rotation or spinning in circles.
Left Stick: Moves the drone up, down, and in 
rotations.

Flight Controls

Please Note: Before every flight, the drone 
will have to be paired to the application.
There are two ways to fly the T.E.D., by 
Gravity Sensor and Throttle Control.

Gravity Sensor: This setting will allow 
your drone to move in any direction that 
you move your phone. In this setting, you 
will not need to move the Directional 
Sticks, however, you will still need to 
control the throttle.
Step 1. With your T.E.D. on and connect-
ed. to the Wi-Fi, tap the Auto Take Off 
button.
Step 2. Keeping your phone horizontal, 
tap the Gravity Sensor by the top of the 
right Throttle Stick.

Step 3. Move your phone in any direction, the 
drone will follow.

Touch Control: The directions below are for 
touch control which requires you to tap the 
Throttle Sticks on the phone. This is the most 
common way of flying drones.

Step 1. With your T.E.D. on and connect-
ed to the Wi-Fi, tap the Auto Take Off 
button.

Step 2. Use the right Directional Stick to 
move around the left Throttle Stick to change 
direction.

Step 3. To land, use the left Throttle Stick 
to go down or press the Auto Landing 
button. 

To come up on your own without the assist of 
Auto Takeoff, follow the below instructions.
Step 1. With your T.E.D. on and connected to 
the WiFi, take the throttle and Directional 
Sticks and push them down and slightly off 
center. This will initiate the blades and bring 
the drone to altitude. 

Step 2. Use the left Throttle Stick to control 
altitude and direction.  Use the right Throttle 
Stick to maneuver forward and backward & 
left and right directions.

Ascending, Descending – 

Left / Right Throttle Stick

Ease the left Throttle Stick upwards to make 
the T.E.D. go higher in altitude. Ease the left 
Throttle Stick downwards to lower the T.E.D.
Turning – Left Throttle Stick
Push the left Throttle Stick left or right to turn 
the T.E.D. in a specific direction.
Forward, Back – Right Directional Stick
Ease the right Directional Stick up and down 
to fly the T.E.D. forward and backward.
Side to Side Flight Left or Right – Right 
Directional Stick
Push the right Directional Stick left or right to 
fly the T.E.D. side to side.

Speed

There are two speeds on the drone 
which can be changed by tapping the 
speed button.

Speed 1: 1 Tap Slow at 30%
Speed 2: 3 Taps Fast at 100%

Landing

Gently press the Auto Landing button 

until landing on the ground. You can also 
initiate an emergency STOP by pressing the 
same button for 3 seconds. 

Please note that 

emergency stopping in mid-air will result 
in the drone dropping immediately and 
may damage the product, please use with 
caution.

Trim

For drifting issues, calibrate the drone back 
to normal trim settings by use the Automatic 
Trim Reset found to the right of the Auto 

Landing button. Please note you must reset 
while drone is connected to your device AND 
on a flat surface (not in flight).
You can also manually reset the trim while in 
flight it. The following are a few adjustments 
that you can make to the flight characteristics 
if the Auto Trim does not fix drifting: 

Forward/Backward Trimmer: If the 
T.E.D. drifts backward or forward, press 
the forward/backward trim button located 
to the left of the Directional Stick until 
centered.
Side to Side Trimmer: If the T.E.D. drifts 
left or right, press the side to side trim 
below the Right Directional Stick until 
centered.
Turning Trimmer: If the T.E.D. is 
spinning in circles or drifting in a rotation, 
press the turning trim button located 
below the left Throttle Stick until 
centered. 

Flying in SmartFly Tech 

mode and using Auto 

Back

The T.E.D. features SmartFly Tech and a 
Auto Back feature. Generally when you 
are flying a drone, your front and back 
usually change position as you rotate 
and fly in different directions. This can 
make it difficult to tell which direction the 
drone is flying in. Therefore, SmartFly 
Tech helps you take control over the 
drone’s directions as forward will always 
be facing the way that you are facing.

Taking Photos & Videos

iPhone Users: When you connect your phone 
to the WiFi, your phone will ask you if you 
want to allow your camera to access photos. 
Choose Yes to allow the drone to take photos 
and save them to your gallery.

Taking Selfies

Step 1. When your drone is stable in flight, 
aim the camera on yourself or subject.

Step 2. Tap the camera or video icon to 
take a photo or video.
Step 3. To view your photos, land your 
drone and tap the Image Gallery button. 
You can either do this on the Home Page 
or by clicking the Gallery icon. 

Step 4. In the Image Gallery, you will see a 
camera icon and a video icon with a list of 
files. These files are your photos. Tap a photo 
to view it or delete it.

Odyssey Toys •  Miami, FL 33179
For Customer Service please email: 
Care@OdysseyToys.com
Please note the units model number and 
name in your email.Extra Parts Avail-
able! Visit Odyssey online to order:
• Extra Batteries
• New rotor blades Model no. ODY-1719

www.OdysseyToys.com

SmartFly Tech Mode

In this mode, you do not need to worry 
about the orientation of the drone. 
Whatever position the drone’s front is in 
before taking off will be your front IF you 
initiate the SmartFly Tech mode. This is 
useful if you would like to have to the 
drone return to your general direction 
(i.e. Auto Back).

Auto Back

In this mode, the drone will return back 
to your general direction automatically. 
However, the drone will return back to 
you IF, and ONLY IF, you are looking 
towards the BACK of the drone. This 
means that if you are facing the backside 
of the drone and you hit the Auto Back 
button, the drone will fly backwards 
towards your general direction. 

Initiating SmartFly Tech & Auto 

Back

Step 1 Before taking off, place the drone 
on a flat surface 
Step 2 Press the SmartFly Tech button, 
which is located above the right joystick. 
Step 3 Take flight and fly the drone. 
When you are ready to return home 
ensure that the back of the drone is 
facing you.
Step 4 Press the Auto Back button, 
which is located at the top middle of the 
app screen.  

Step 5. Your photos/videos are also saved to 
your phone’s camera roll. To view the photos, 
go to your gallery and looking at the most 
recent photos and/or accessing the T.E.D. 
folder your phone has created for the photos. 
Step 6. Share your photos with your friends!