PF 33 MT - PF 46 MT
General specifications and warning
EN - 2
1.1 - GENERAL WARNINGS
- Before setting the machine at work the operator
should have carefully red these instructions
and have acquired a deep knowledge of the
technical specifications and control devices.
- To the operator is suggested to attend a
training course on the use of the machine.
- Before installing the machine make sure that
the used area is compatible with the dimensions
and the weight of the machine.
- For the installation or removal of any machine
part, the used lifting and handling devices should
be suitable to the weight and geometrical char-
acteristics of the part to be lifted or handled.
- Only skilled and authorized personnel is allowed
to start adjust or repair the machine. This hand-
book should be always consulted before to do
any work on the machine.
- Mechanical parts and electrical components
inside the machine are protected by totally
enclosed panels fastened with screws.
- Before performing any cleaning and/or mainte-
nance on the machine, and before removing any
protection, make sure that the LINE DISCON-
NECTING SWITCH upstream of the device
is switched “OFF”, and that its status can be
seen by the operator working on the machine.
- If the power supply cable is damaged, it can be
replaced by the manufacturer or by its techni-
cal support service or by a person with similar
qualifications in order to prevent any type of
risk.
- The power supply system of the purchaser
should be provided with an automatic release
device above the machine main switch and with
a suitable earthling system complying with the
accident prevention regulations.
- In case of repairs to be done on the main switch
or in the main switch area, turn off the power
of the electrical line.
- Any inspection and maintenance works requir-
ing the removal of the safety protections are
made under the responsibility of the user.
Therefore it is recommended that the above
mentioned works are done by authorized
and skilled personnel only.
- Make sure that all safety devices (barriers,
protections, carter, micro-switches, etc.) have
not been tampered and are perfectly working.
On the contrary, they should be repaired.
- Do not remove the safety devices.
- In order to avoid personal risks, only suitable
tools should be used, in accordance with the
local safety regulations.
- Do not tamper the electric and pneumatic plant
or any other mechanism for any reason.
- Do not leave the machine unattended while it
is working.
- This device can be used by children older than
8 years or by people with diminished physical,
sensorial or mental capacities, or without ex-
perience or required knowledge, provided they
are supervised or have received instructions on
safe use of the device and understanding its
risks. Children must not play with the device. The
cleaning and maintenance to be performed by
the user must not be done by children without
supervision.
- Wear safety clothing only, approved by the law
in force.
- In case of works to be done in a position that
cannot be reached from the ground, use safe
ladders or lifting devices only, in conformity with
the local safety regulations.
- In case of repairs to be done near or under the
machine, make sure that:
• there are no machine members that can start
working and/or instable parts placed on the
machine or near the machine.
- Do not use your hands instead of suitable tools
to work on the machine.
- Do not use your hands or other tools to stop
any moving parts.
-
Do not use matches, lighters or flames near
the machine.
- YOUR BEST ATTENTION SHOULD BE PAID
TO THE WARNING PLATES LOCATED ON
THE MACHINE BEFORE DOING ANY WORK
ON THE MACHINE OR NEAR THE MACHINE.
Chapter 1
Summary of Contents for PF 33 MT
