PF 33 MT - PF 46 MT
General specifications and warning
EN - 3
- The user is obliged to keep all the warning plates
in legible conditions and, if required, to change
their position in order to make them fully visible
to the operator.
- Moreover the user is obliged to replace any
warning plate that, for any reason, has been
damaged or is not clearly legible. New warning
plates can be obtained through our Technical
Service Centre.
- Stop the machine before doing any repair
work.
- In case of malfunction of the machine or dam-
ages to its components, get in touch with the
maintenance engineer and do not try to repair
the machine.
- It is absolutely prohibited to use the machine
for other purposes different from those ex-
pressly indicated and documented.
Use of the machine must always take place
with the methods, timing and location set out
by good technical practice, in accordance with
machine directive 2006/42 and complying with
workplace health and safety standard as set
out by current laws of the country where the
machine is used.
- Company manufacturer or its Agent declines
all responsibility for any accident or damage
to persons or properties arising from the
non compliance with the safety regulations
and the directions of this booklet.
- THESE SAFETY REGULATIONS INTEGRATE
OR COMPLEMENT THE LOCAL SAFETY
REGULATIONS.
- DO NOT make hurried or inaccurate repairs
that may compromise the good running of
the machine and the safety of the operator.
- IN CASE OF DOUBT ALWAYS ASK FOR THE
PRESENCE OF SKILLED PERSONNEL.
- FOR ANY ELECTRIC/ELECTRONIC OR
MECHANIC TAMPERING OF THE MA-
CHINE BY THE USER OR IN CASE OF A
NEGLIGENT USE OF THE MACHINE, THE
MANUFACTURER IS RELIEVED FROM ANY
RESPONSIBILITY AND THE USER WILL BE
THE ONLY ONE RESPONSIBLE AGAINST
THE COMPETENT AUTHORITIES FOR THE
ACCIDENT PREVENTION.
1.2 - REFERENCE NORMATIVE
- The machine and its safety components have been
manufactured in compliance with the directives indi-
cated in the declaration of conformity.
1.3 - DESCRIPTION OF THE SYMBOLS
Many accidents are caused by a poor knowledge of
and by a non compliance with the safety regulations
to put into practice during the functioning and main-
tenance works to be done on the machine.
In order to avoid any accidents, read understand
and follow all the warnings and cautions contained
in this booklet and those written on the plates located
on the machine.
To identify the safety messages included in this book-
let, following symbols have been used:
DANGER
This symbol is used in the safety messages con-
tained in the booklet in case of potential danger
situations or possibility to cause serious injuries
or dead.
ATTENTION
This symbol is used in the safety messages of the
booklet for any danger situation that, if disregarded,
may cause small or moderate injuries or damages.
The message can be used also in case of danger
situations that may cause damages to the machine.
☞
IMPORTANT
This symbol is used in case of precautionary meas-
ures to be taken in order to avoid any operation that
may reduce the life of the machine or for important
communication to the operator.
DANGER
For clarity reasons, some illustrations of this booklet
show the machine without safety guards. DO NOT
USE THE MACHINE WITHOUT SAFETY GUARDS.
Summary of Contents for PF 33 MT
