3
Operating Instructions and Parts Manual
24854
HEAVY-DUTY 22 TON
JACK STANDS
4/17
2017 OEMTOOLS
™
33. The procedures documented in this manual are to
serve as guidelines for the use of this equipment.
34. In addition to these guidelines, always follow the
manufacturer’s recommended procedures when
servicing each unique vehicle.
35. The use of this equipment is simple and straightforward
if you follow the instructions. When operating this
equipment, use common sense, and only use this jack
stand for its intended purpose.
PRODUCT DESCRIPTION
Axle Stands are designed to support rated capacity,
partial vehicle loads consisting of one end of a
vehicle. Use as a matched pair to support one end of
a vehicle only.
PRODUCT SPECIFICATIONS
Capacity
22 Tons
Min. Height 12.24"
Max. Height 19.88"
Weight
79.4 Lbs.
SPECIFIC SAFETY INSTRUCTIONS AND WARNINGS
1. Never use the jack stand for any purpose other than
the information in this manual.
2. Verify that the product and application are compatible;
if in doubt call OEMTOOLS™ at 1-866-458-2472.
3. Before using this product, read the operator’s manual
completely and familiarize yourself thoroughly with the
product, its components and recognize the hazards
associated with its use.
4. Wear appropriate safety gear, including heavy-duty
work gloves and ANSI-approved safety goggles
during use.
5. DO NOT exceed the weight capacity of the jack stand.
Make sure weight is evenly distributed. Be aware of
dynamic loading. Sudden load movement may briefly
create excess load, causing product failure. Exceeding
the maximum capacity for this product is dangerous
and can lead to serious injury or property damage.
6. Always evaluate your task before using this jack stand.
Use only as intended.
7. Use only on a hard, level and flat surface capable of
bearing the combined weight of the jack stand, load
being lifted, the operator and any tools being used.
WARNING
:
Never load the jack stand with an engine that extends
beyond the centerlines of the front and rear wheel/
caster axles.
1. If you are working and the load becomes off-balance
and/or the jack stand begins to tip over, DO NOT
ATTEMPT TO CATCH OR LIFT THE LOAD WHEN
FALLING. SERIOUS PERSONAL INJURY CAN RESULT.
In this event, clear the area as quickly and safely as
possible in order to avoid injury from the falling load,
including getting hit with flying fragments.
2. Before each use, inspect the general condition of the
jack stand. If a problem occurs, have the problem
corrected before further use.
WARNING
:
To prevent serious injury, DO NOT use a damaged or
malfunctioning jack stand.
3. If in doubt about the safety of your project, we advise
you to have the work done by a professional familiar
with applicable safety practices.
ASSEMBLY
1. Insert extension tube in stand base.
OPERATION
WARNING
:
Support areas of vehicle specified by vehicle
manufacturer. Use ONLY on vehicles whose support
points are compatible with saddle of axle stand.
Incompatibility may result in structural damage to vehicle
and/or axle stand.
1. With vehicle lifted, carefully locate the desired support
points
2. With the axle stands at their lowest position, carefully
position them directly under the desired support points
with load centered on the extension tube saddle
3. Adjust saddle height by lifting up the extension
tube, then insert the tube support bar through the
appropriate hole on extension tube.
4. Check to ensure support bar is secured and nested
across two corresponding radii before loading. Ensure
that the support bar is inserted completely so that the
bar stop engages the collar.
5. Slowly lower the vehicle onto the stands.
6. Check to ensure vehicle is secured before working
on, around or under. Use wheel chocks on all unlifted
wheels in both directions to prevent inadvertent
movement.
REMOVING AXLE STANDS
WARNING
:
Clear all tools and personnel before lowering load.
1. With suitable jack, raise vehicle clear of stands.
2. Carefully remove support bar and allow extension tube
to drop down to lowest position.
3. Remove axle stands, then slowly lower vehicle.
MAINTENANCE
Periodically inspect each stand. Ensure all parts move
freely. DO NOT apply oil or grease to any portion of this
product.
NOTE: If rust appears, sand affected area and cover with
suitable utility paint.
STORAGE
Store stands in upright position and in a clean, dry area.
