2
Operating Instructions and Parts Manual
26038
7/21
2021 OEMTOOLS
®
AIR BLOW AND
SUCTION GUN
IMPORTANT INSTRUCTIONS
AND SAFETY RULES
1. Know your tool. Read this manual carefully. Learn the tool’s
applications and limitations, as well as potential hazards specific
to it.
2. Keep work area clean and well lit. Cluttered or dark work areas
invite accidents.
3. Keep children away. All children should be kept away from the
work area. Never let a child handle a tool without strict adult
supervision.
4. DO NOT operate this tool if under the influence of alcohol or
drugs. Read warning labels on prescriptions to determine if your
judgment or reflexes are impaired while taking drugs. If there is
any doubt, DO NOT attempt to operate.
5. Use safety equipment. Eye protection should be worn at all times
when operating this tool. Use ANSI approved safety glasses.
Everyday eyeglasses are NOT safety glasses. Dust mask, non-
skid safety shoes, hard hat or hearing protection should be used
in appropriate conditions.
6. Wear proper apparel. Loose clothing, gloves, neck-ties, rings,
bracelets or other jewelry may present a potential hazard when
operating this tool. Keep all apparel clear of the tool.
7. DO NOT overreach. Keep proper footing and balance at all times
when operating this tool.
8. Check for damage. Check your tool regularly. If part of the tool
is damaged, it should be carefully inspected to make sure that it
can perform its intended function correctly. If in doubt, the part
should be repaired. Refer all servicing to a qualified technician.
Consult your dealer for advice.
9. Keep away from flammables. DO NOT attempt to operate this tool
near flammable materials or combustibles. Failure to comply may
cause serious injury or death.
10. Store idle tools out of the reach of children and untrained
persons. Tools may be dangerous in the hands of untrained users.
11. Maintain tools with care.
12. Keep tools dry and clean.
13. Properly maintained tools are less likely to bind and are easier
to control. DO NOT use a damaged tool. Tag damaged tools “DO
NOT use” until repaired.
14. Check for misalignment or binding of moving parts, breakage of
parts, and any other condition that may affect the tool’s operation.
15. If damaged, have the tool serviced before using. Many accidents
are caused by poorly maintained tools.
16. Use only accessories that are recommended by the manufacturer
for your model. Accessories that may be suitable for one tool may
become hazardous when used on another tool.
17. Tool service must be performed only by qualified repair
personnel. Service or maintenance performed by unqualified
personnel could result in a risk of injury.
18. When servicing a tool, use only identical replacement parts. Use
of unauthorized parts or failure to follow maintenance instructions
may create a risk of injury.
19. Maintain a safe working environment. Keep the work area well lit.
Make sure there is adequate surrounding workspace. Keep the
work area free of obstructions, grease, oil, trash, and other debris.
DO NOT use this product in a damp or wet location.
20. Maintain labels and nameplates on this product. These carry
important information. If unreadable or missing, contact
OEMTOOLS
®
for a replacement.
21. Keep the handle dry, clean, and free from brake fluid, oil, and
grease.
22. Before use, read and understand all warnings, safety precautions,
and instructions as outlined in the vehicle manufacturer’s service
manual. It is beyond the scope of this manual to properly describe
the correct procedure and test data for each vehicle.
23. The warnings, precautions, and instructions discussed in this
manual cannot cover all possible conditions and situations that
may occur. The operator must understand that common sense
and caution are factors which cannot be built into this product,
but must be supplied by the operator.
24. We believe the information contained herein to be reliable.
However, general technical information is given by us without
charge and the user shall employ such information at their own
discretion and risk. We assume no responsibility for results or
damages incurred from the use of such information in whole
or in part. Always refer to specific instructions and technical
information supplied by vehicle manufacturer.
25. The manufacturer declines any and all responsibility for damage
to vehicles or components if said damage is the result of
unskillful handling by the operator or of failure to observe the
basic safety rules set forth in the instruction manual.
26. The procedures documented in this manual are to serve as
guidelines for the use of this equipment.
PRODUCT DESCRIPTION
The OEMTOOLS
®
Air and Blow Suction Gun was developed for quick
and easy clean up, designed with a one touch button that will change
the gun from blow to suction mode.
PRODUCT SPECIFICATIONS
Maximum Air Pressure
90 psig, 6.2 bar
Air Consumption
3.36 CFM
Air Inlet Thread Size
1/4" PT(NPT)
Recommended Hose Size
3/8"
Suction Power
9 cmHg (with dust bag)
Minimum Hose Size
5/16" I.D.
Sound Pressure Level
97 dBA
Vibration
0.4m/s2
Length
5.7"
Weight
0.88 Lb.
CONTENTS
Housing Assembly (1), Deflector (1), Dust Bag (1), Clamp Ring (1),
Extension Tube (1), Flexible Hose Assembly (1), Small Diameter
Vacuum (1), Flat Tube (1), Brush (1)
