background image

TROUBLE SHOOTING

The following guide will assist you with most problems that may be encountered when
laminating.

PROBLEM:

Laminator is inoperative.  Motor does not run, indicator lights
are out.

ACTION:

Unit may be unplugged.  Connect power supply.

Ensure that your circuit breaker has not tripped.

Fuse may have blown.  Replace fuse (back next to power cord) with 15amp
BUSS (MDA-15).

PROBLEM:

Laminating film and item being laminated move through lamina-
tor erratically.

ACTION:

Check thickness of item to be laminated.  Maximum thickness is 1/16”
(1.6mm) if rollers have not been adjusted.

Clean heat shoes of residual adhesive.  Refer to MAINTENANCE section
for cleaning instructions.

PROBLEM:

Plastic is not bonding to the item or to itself at the edges.

ACTION:

Make sure heat shoes and rollers are at proper operating temperature and
have had time to warm up.  See table 1 for the suggested temperature
ranges.

PROBLEM:

Wrinkles appear on the laminated items running parallel with the out-
 side edges.

ACTION:

Increase roller tension on top and/or bottom supply rolls.

Reduce heat shoe temperature.

Clean heat shoes of residual adhesive.  See MAINTENANCE section for
cleaning instructions.

12

1-800-543-5454

www.officezone.com

OfficeZone

Summary of Contents for MightyLam 2700



























Reviews: