background image

9

Officine Gullo

CHECKING FOR ADEQUATE VENTILATION

Make sure that the air intake into the room where the appliance is installed is sufficient for an 

adequate change of air, as specified by regulations in effect.

The appliances installed in buildings open to the public must satisfy the following requirements.

Installation rules

The installation and maintenance of the appliance must be done according to the correct proce-
dures and regulation

texts in use, particularly:

• safety standards for the prevention of fire and panic.

Connection and installation of appliance, ventilation and exhaust removal systems, shall be done 

according to the Manufacturer’s instructions and by qualified technicians and according to the 

regulations in effect. The electric wiring shall conform to the regulations in effect. 

All fire prevention codes shall be observed.

a) General indications 

(Rules valid for GB only)

- For all appliances:

Gas safety Regulations, 1984; Health and safety at Work Act, 1974 Codes of Practice, BS 8173, 
1982, The Building
Regulations 1985; The Building Standards Regulations, 1981, the IEE Regulations and the by-
laws of the local Water Undertaking.
The local gas Region or LPG supplier and the local authority and the relevant recommendation 
of the British Standards (latest editions) concerned.
The installation, transformation and repair of appliances for professional kitchens as well as re-
moval due to malfunction, and the supply of gas, may be made only by means of a maintenance 

contract stipulated with an authorized sales office and in observance of technical regulations.

The appliance can be installed by itself or in a series side by side with appliances produced by us. 
There must be a minimum distance of at least 10 cm between the appliance and the sides of the 

nearby cabinets made of inflammable material. 

Take suitable measures to guarantee thermal insulation of the inflammable sides, such as, for 

example, the installation of protection against radiation. 
The appliances must be installed in a suitable manner, observing the safety standards. 
The small feet are adjustable to level the appliance.

Summary of Contents for DWFS4

















Reviews: