Officine Gullo GGS8P, Instructions Manual

Officine Gullo

18

ELECTRIC TECHNICAL DATA TABLE

MODEL

Dimensions

cm

Power Supply

Tot. 

power 

(KW)

Max. 

absorb

A

Power 

supply 

cable mm²

GGS8P

80x70x90h

230V~ 50/60 Hz

0,01

0,04

5x1

GES8P

80x70x90h

400V~3N 50/60 Hz

5

10,4

5x1,5

GGS12P

120x70x90h

230V~ 50/60 Hz

0,01

0,04

5x1

GES12P

120x70x90h

400V~3N 50/60 Hz

5

10,4

5x1,5

GGPS8P

80x70x90h

230V~ 50/60 Hz

0,01

0,04

5x1

GEPS8P

80x70x90h

400V~3N 50/60 Hz

5

10,4

5x1,5

GGPS12P

120x70x90h

230V~ 50/60 Hz

0,01

0,04

5x1

GEPS12P

120x70x90h

400V~3N 50/60 Hz

5

10,4

5x1,5

INSTALLATION

• 

The operations for installing, conversions for use with other types of gas and starting up must be done only 

by qualified personnel whose qualifications comply with the norms in force.

• 

Gas installations, the electrical connections and the rooms in which the appliances are installed must comply 

with the norms in force in the Country in which the installation is carried out; above all, the appliance must 

be installed in a well ventilated room, preferably under an extractor hood, so as to ensure the complete 

extraction of gas emissions which are formed during combustion. The air necessary for combustion is 

2m3/h per kW of power installed.

Attention:

 In accordance with international rules, when connecting the appliance, an automatic device enabling the 

disconnection of all contacts from the mains, must be installed above it; this device must have a contacts opening 

of at least 3 mm.

19

Officine Gullo

CHECKING FOR ADEQUATE VENTILATION

Make sure that the air intake into the room where the appliance is installed is sufficient for an adequate change of air, as 

specified by regulations in effect.

The appliances installed in buildings open to the public must satisfy the following requirements.

Installation rules

The installation and maintenance of the appliance must be done according to the correct procedures and regulation

texts in use, particularly:

• safety standards for the prevention of fire and panic.

Connection and installation of appliance, ventilation and exhaust removal systems, shall be done according to the 

Manufacturer’s instructions and by qualified technicians and according to the regulations in effect. The electric wiring shall 

conform to the regulations in effect. 

All fire prevention codes shall be observed.

a) General indications 

(Rules valid for GB only)

- For all appliances:

Gas safety Regulations, 1984; Health and safety at Work Act, 1974 Codes of Practice, BS 8173, 1982, The Building

Regulations 1985; The Building Standards Regulations, 1981, the IEE Regulations and the by-laws of the local Water 

Undertaking.

The local gas Region or LPG supplier and the local authority and the relevant recommendation of the British Standards 

(latest editions) concerned.

The installation, transformation and repair of appliances for professional kitchens as well as removal due to malfunction, 

and the supply of gas, may be made only by means of a maintenance contract stipulated with an authorized sales office 

and in observance of technical regulations.

The appliance can be installed by itself or in a series side by side with appliances produced by us. 

There must be a minimum distance of at least 10 cm between the appliance and the sides of the nearby cabinets made 

of inflammable material. 

Take suitable measures to guarantee thermal insulation of the inflammable sides, such as, for example, the installation of 

protection against radiation. 

The appliances must be installed in a suitable manner, observing the safety standards. 

The small feet are adjustable to level the appliance.

PIPE FOR GAS CONNECTION

The gas connection must be done with steel or copper pipes, or otherwise with flexible steel pipes in compliance 

with the national norms, if any exist. Each appliance must be provided with a cut-off cock for rapid interruption of the 

gas supply. Once the appliance has been installed, it is necessary to check for gas leaks for the pipe fittings; do not 

use a flame for this purpose but a non-corrosive substance such as soapy water or foamy substances as contained 

in leakfinder sprays. All our appliances undergo careful testing: the type of gas, the operating pressure and the 

category are indicated on the data plate.

NB:

 The year of the appliance manufacture is shown in item “N” on the data plate. The first two numbers (e.g. 08..) 

represent the year of manufacture.