background image

Valor™ 2000W Series                                                                         EN-15

 

 

6.3 Compliance

 

Compliance to the following standards is indicated by the corresponding mark on 
the product. 

Mark 

Standard 

 

This product conforms to the EMC Directive 2004/108/EC, the Low 
Voltage Directive 2006/95/EC. The Declaration of Conformity is 
available online at 
europe.ohaus.com/europe/en/home/support/compliance.aspx. 

 

AS/NZS CISPR 11 

 

CAN/CSA-C22.2 No. 61010-1-12 
UL Std. No. 61010-1 (3

rd

 edition) 

 

NSF/ANSI 169–2009 

 

NSF/ANSI/3-A 14159-1-2010 

 

Disposal 

 

In conformance with the European Directive 2002/96/EC on Waste 
Electrical and Electronic Equipment (WEEE) this device may not be 
disposed of in domestic waste. This also applies to countries outside 
the EU, per their specific requirements. 
The Batteries Directive 2006/66/EC introduces new requirements 
from September 2008 on removability of batteries from waste 
equipment in EU Member States. To comply with this Directive, this 
device has been designed for safe removal of the batteries at end-of-
life by a waste treatment facility. 

Please dispose of this product in accordance with local regulations at the collecting 
point specified for electrical and electronic equipment. If you have any questions, 
please contact the responsible authority or the distributor from which you 
purchased this device. 
Should this device be passed on to other parties (for private or professional use), 
the content of this regulation must also be related. 
Disposal instructions in Europe are available online at 
europe.ohaus.com/europe/en/home/support/weee.aspx. 
Thank you for your contribution to environmental protection. 

 

www.

GlobalTestSupply

.com

Find Quality Products Online at:

sales@GlobalTestSupply.com

Summary of Contents for Valor 2000W Series


















Reviews: