background image

 

 

 

 

                                       7  

 

 

             

            

the possibility for loss of control. Also your tires may 
overheat, increasing the possibility of a blowout. 

^

 

WARNING

Driving too fast for conditions can result in 
loss of control and cause death or serious 
injury. 

Adjust speed down when towing trailer.

2.2.3  Adjust Driving When Towing Trailer

When towing a trailer, you will have decreased 
acceleration, increased stopping distance, and 
increased turning radius. 

The trailer will change the handling characteristics of 
the tow vehicle, making it more sensitive to steering 
inputs and more likely to be pushed around in windy 
conditions or when being passed by large vehicles. In 
addition, you will need a longer distance to pass, due 
to slower acceleration and increased length. With this 
in mind:

• 

When encountering trailer sway, take your foot 
off the accelerator, and steer as little as possible 
in order to stay on the road. Use small “trim-like” 
steering adjustments. Do not attempt to steer out 
of the sway; you’ll only make it worse. Also do 
not apply the tow vehicle brakes to correct trailer 
swaying. On the other hand, application of the 
trailer brakes alone will tend to straighten out the 
combination, especially when going downhill.

• 

Check rearview mirrors frequently to observe trailer 
and traffi c.

• 

Be aware of trailer height, especially when 
approaching bridges, roofed areas and trees.

• 

Be alert for slippery conditions. You are more likely 
to be affected by slippery road surfaces when 
driving a tow vehicle with a trailer, than driving a 
tow vehicle without a trailer.

• 

Anticipate the trailer “swaying.” Swaying can be 
caused by excessive steering, wind gusts, roadway 
edges, or by the trailer reaction to the pressure 
wave created by passing trucks and busses.

• 

Use lower gear when driving down steep or long 
grades. Use the engine and transmission as a 
brake. Do not ride the brakes, as they can overheat 
and become ineffective.

2.2.4  Trailer Not Properly Coupled To Hitch

It is critical that the trailer be securely coupled to 
the hitch, and that the safety chains and emergency 
breakaway brake lanyard are correctly attached. 
Uncoupling may result in death or serious injury to 
you and to others.

^

 

WARNING

Proper selection and condition of the 
coupler and hitch are essential to safely 
towing a trailer. 

A loss of coupling may result in death or 
serious injury.

Hitch size must match coupler size.

Be sure hitch load rating is equal to or 
greater than load rating of the coupler.

Be sure hitch components are tight before 
coupling trailer to tow vehicle.

Observe hitch for wear, corrosion and 
cracks before coupling. Replace worn, 
corroded or cracked hitch components 
before coupling trailer to tow vehicle.

^

 

WARNING

An improperly coupled trailer can result in 
death or serious injury. Do not move the 
trailer until:

• 

Coupler is secured and locked to hitch.

• 

Safety chains are secured to tow 
vehicle.

• 

Trailer jack(s) are fully retracted.

• 

Trailer brakes are checked.

• 

Tires and wheels are checked.

• 

Breakaway switch is connected to tow 
vehicle;

• 

The trailer lights are connected and 
checked.

• 

Load is secured to trailer.

Safety

Summary of Contents for Utility Trailer





















































Reviews: