background image

v

6600-0371-000

10/27/03

Table of Contents

v

w

w

w

w

w

Warnings

Before using the Ohmeda Medical Panda

TM

 Baby Warmer System, read this

entire manual. Attempting to use this device without a thorough understanding
of its operation may result in patient or user injury. This device should only be
operated by personnel trained in its operation and under the direction of qualified
medical personnel familiar with the risks and benefits of this type of device.
Additional precautions specific to certain procedures are found in the
text of this manual.

Do not use the Warmer in the presence of flammable anesthetics; a possible
explosion hazard exists under these conditions.

Do not perform the Checkout Procedures (Mechanical and Control Unit) while a
patient occupies the Warmer.

Complete the “Checkout Procedures” section of this manual before putting the
unit into operation. If the warmer fails any portion of the checkout procedures it
must be removed from use and repaired.

Do not use the Warmer system if the system failure alarm is activated. Remove
the unit from service and refer to qualified personnel for repair.

w

w

w

w

w

Cautions

Only competent individuals trained in the repair of this equipment should
attempt to service it as detailed in the service manual. The Service Manual
provides detailed information solely for use by individuals having proper
knowledge, tools and test equipment, and for service representatives trained
by Ohmeda Medical.

General Precautions

6600−0371−000−DWG

100

MANUAL−DOC, User Reference Manual, OM Panda, English−default

Reproduced from the electronic master in MATRIX

Summary of Contents for Panda





















Reviews: