background image

  Use only the AC adapter supplied with this machine otherwise it may 
                             result in a fire or electric shock.

  

            

Do not scratch the rail. Do not apply any oil or grease to the rail.

  

            

Use specified screws only. Avoid using screws to which oil, grease, dirt, or other foreign matter is attached.

  

            

When picking up screws, exercise care not to apply any undue force or shock.

  

            

Do not position your fingers or foreign objects in the screw bin, holes, or other open spaces as it may cause injury.

                             Be sure that no inappropriate screws or foreign objects used with this machine. 

  
 

      

             If any abnormality occurs during operation, turn off the power switch and disconnect the AC adapter from the

 

            

power outlet.

            

If you continue to operate this machine while it is acting abnormally, a risk of fire, electric shock, or personal

                             injury

 

may be caused. If you encounter any abnormality, contact your local dealer.

  
   

      

          When this machine is in need of repair, contact your local dealer.

Rail 

AC adapter

Incompatible screws 

Screw access precautions

Avoid inserting foreign objects

Abnormalities during operation

Avoid making attempt to repair, disassemble, or modify this machine

 -

CAUTION

CAUTION

CAUTION

CAUTION

When the earth wire is connected, loosen the screw near the        mark once.

After attaching the earth wire,tighten the screw again.

the bottom of the main body

Ground wire

Summary of Contents for NJ-2320



























Reviews: