background image

CAUTION:

PINCH POINTS!  Keep fingers, hands and

cables out of pinch point areas.

6. Pull downward on the pullstraps and swing inward toward

wall, latching interface brackets to lower bar and locking

bottom of screen to the mount. (See Figure 12)

Figure 10

(Y) x 4

Figure 9

Center of bracket

Pull strap

Installation and User’s Guide

http://www.oickorea.com

8

Attaching Interface Brackets to TV

1. Align the center of the pull-out uprights (U and V) with center

of screen. (See Figure 9)

NOTE:

The diamond-shape hole in the bracket corresponds to

the center of the mount.

WARNING:

IMPROPER INSTALLATION CAN LEAD TO

DISPLAY FALLING CAUSING SERIOUS PERSONAL

INJURY OR DAMAGE TO EQUIPMENT! Using screws of

improper size may damage your display. Properly sized

screws will easily and completely thread into display

mounting holes. If spacers are required, be sure to use longer

screws of the same diameter.

2. Select correct screws, spacers (if necessary) and universal

washers from the hardware bag (A-N) and attach brackets

(U and V) to back of screen. (See Figure 9)

NOTE:

Uprights may need to be pulled out to the extended

position in order to install screws through proper holes.

Attaching Screen to Wall Mount

1. Attach wall bracket caps (Y) to top and

bottom of both wall brackets. (See Figure 10)

2. Adjust Velcro® pull strap (if necessary) so it does not

extend beyond bottom of screen. (See Figure 11)

NOTE:

Do NOT allow both interface brackets (U and V) to be

located on same side of wall bracket. (See Figure 11)

NOTE:

NEVER place both interface brackets (U and V) to one

side of the wall mount center line! (See Figure 11)

Figure 11

Both interface brackets must NEVER be located

to one side of the wall brackets!

Pullstrap

NEVER place both interface brackets to one

side of the wall mount center line (CL)!

Center Line (CL)

3. Hang top hook of interface brackets (U and V) onto the top

bar of the mount (R). (See Figure 12)

4. Slide screen and bars to desired viewing position.
5. Route cables between wall and bars.

NOTE:

The pull-out feature allows the screen to be pulled away

from the wall for easy cable access following

installation.

403-403, Bucheon Technopark 4 Danji Apt., 193, Yakdae-dong,
Wonmi-gu, Bucheon-si, Gyeonggi-do 420-734, Korea 

Tel. +82-70-7510-2544  /  Fax. +82-70-8240-4403
Email. sales@oickorea.com

Summary of Contents for MICRO-ADJUSTABLE PULL-OUT











Reviews: