background image

NEXO NLX1_INDEX 

OJMAR 

1

 

 

INDEX 

 

1. NEXO NL1 LOCK INSTALLATION AND ASSEMBLY .................................................................................................... 2

 

1.1 GENERAL WARNINGS ............................................................................................................................................... 2

 

1.1.1 Regulatory information USA .................................................................................................................................. 2

 

1.1.2 Class B device notice ............................................................................................................................................. 2

 

1.1.3 RF exposure safety ................................................................................................................................................. 3

 

1.1.4 TECHNICAL SUPPORT ........................................................................................................................................... 3

 

1.2 Lock directions .......................................................................................................................................................... 3

 

1.3 Assembly considerations .......................................................................................................................................... 4

 

1.3.1 Ojmar striking plate .................................................................................................................................................. 4

 

1.3.2 Assembly with Magnetic Catch Latch ...................................................................................................................... 4

 

1.4 Procedure for assembling ........................................................................................................................................ 5

 

2 PROCEDURE TO UNMOUNT THE LOCK ...................................................................................................................... 8

 

3 BATTERY REPLACEMENT......................................................................................................................................... 10

 

4 CLEANING ................................................................................................................................................................ 11

 

 

 
 
 
 
 
 
 

Summary of Contents for NEXO NL1














Reviews: