2
1
3
4
5
6
7
CHECKING THE EQUIPMENT STATUS WITH TopAccess
- 48 -
1C6B
Terminal mail address error
Ask your administrator to check the SMTP Authentication method or if there is
an unpermitted character in the Terminal mail address. Set the correct SMTP
Authentication method or delete the unpermitted character in the Terminal mail
address.
1C6C
Destination mail address error
Check if there is an unpermitted character in the Destination Email address.
Delete the unpermitted character and reset the appropriate Destination Email
address, then try again.
1C6D
System error
Turn the power OFF and then back ON. Perform the job in error again. If the
error still occurs, contact your service representative.
1C70
SMTP client OFF
Ask your administrator to enable the SMTP Client and perform the job again.
1C71
SMTP authentication error
Confirm that the login name and password are correct. If SSL is enabled, make
sure that SSL port number is correctly set.
1C72
POP Before SMTP error
Confirm that the POP Before SMTP settings and POP3 settings are correct.
1CC0
Job canceled
The job was canceled.
1CC1
Power failure
Check whether the power cable is connected properly and is inserted securely.
Check whether the power voltage is unstable.
3A10
MIME format error
Ask the sender to resend the Email in the MIME1.0 format.
3A20
Email process error
Ask the sender to resend the Email.
3A30
Partial Email timeout error
Ask the sender to resend the Email, or change the Partial Wait time setting.
3A40
Invalid partial Email received
Ask the sender to resend the partial Email in the RFC2046 format.
3A50
HDD full error
Ask the sender to resend the Email by separating it into several Emails. If this
error occurs due to running out of paper and too many waiting jobs being
stored in the hard disk, add paper to activate the other jobs.
3A70
Interrupt partial Email reception
Ask your administrator to enable the Enable Partial Email setting and ask the
sender to resend the Email.
3A80
Partial Email disabled
Ask your administrator to enable the Enable Partial Email setting and ask the
sender to resend the Email.
3B10
Email format error
Ask the sender to resend the Email.
3B20
Content-Type error
Ask the sender to resend the Email with attached files that are TIFF format.
3B40
Email decode error
Ask the sender to resend the Email.
3C10, 3C13
TIFF analysis error
Ask the sender to resend the Email with attached files that are TIFF format.
3C20
TIFF compression error
Ask the sender to resend the Email with attached TIFF files in the MH, MR,
MMR, or JBIG compression.
3C30
TIFF resolution error
Ask the sender to resend the Email with attached TIFF files whose resolution is
either 200 x 100, 200 x 200, 200 x 400, 300 x 300, or 400 x 400 dpi.
3C40
TIFF paper size error
Ask the sender to resend the Email with attached TIFF files that can be printed
on paper permitted for the equipment.
3C50
Offramp transmission error
Ask the sender to specify the correct fax numbers and resend the Email.
3C60
Offramp security error
Confirm that the specified fax numbers are registered in the address book of
the equipment. If not, register the fax numbers in the address book and ask the
sender to resend the Email with the correct fax numbers.
3C70
Power failure
Confirm that the job is recovered or not. If not, ask the sender to resend the
Email.
3C90
OffRamp Fax transmission disable error
Confirm if the Fax Send Function of MFP setting is disable or not.
3D10
Destination address error
Ask your administrator whether the DNS and mail server settings are correctly
set. If they are, ask the sender to confirm that the destination address is
correct.
3D20
Exceeding maximum offramp destinations
Ask the sender to specify up to 40 destinations for one offramp gateway job.
The equipment cannot perform offramp gateway transmission for more than 40
destinations.
3D30
Fax unit is not installed
Make sure that the Fax unit is installed, or connected correctly.
3E10
POP3 server communication error
Ask your administrator whether the POP3 server address is correctly set, and
whether the POP3 server works properly. If SSL is enabled, make sure that
SSL port number is correctly set.
3E20
POP3 server communication timeout
Ask your administrator whether the POP3 server works properly and the LAN
cable is connected to the server.
3E30
POP3 login error
Ask your administrator whether the POP3 user name and password are set
correctly.
Error Code
Problem Description
Corrective Action
Summary of Contents for MB760dnfax
Page 1: ...User s Manual Troubleshooting Guide...
Page 79: ...2 1 3 4 3 Battery Disposal P 80 Appendix...
Page 81: ...2 1 3 4 4 Index...
Page 83: ...May 2013 45611502EE Rev1...