manualshive.com logo in svg

Oki MC573, Advanced Manual


Share
Download
background image

- 285 -

7. Troubleshooting

• The received fax is not printed on the appropriate paper.

• Junk faxes are received.

If problems have occurred in the fax communication, print the Transmit/Receipt Journal and 
check the error codes. 

Follow the solution to handle the problem.

For information on how to print the Transmit/Receipt Journal and to see the report, refer to "Items on Transmit and 
Receipt Journal Report".

Other Problems (Fax)

Point to check

Solution

Reference

Did you specify any paper type in a 
tray other than [Plain] or [Recycled] in 
[Media Type]?

Specify [Plain] or [Recycled] in 
[Media Type] for the paper type in the 
tray.

Setting a Print Method for When 
a Received Image Exceeds 
Paper Size

Point to check

Solution

Reference

Is [Block Junk Fax] set to [OFF]?

On the touch panel, press [Device 
Settings] > [AdminSetup] > [Fax 
Setup] > [Other Settings] > [Block 
Junk Fax] > Set [Setting] to [Mode1].

Block Junk Fax

Fax Error Codes

Error 

code

Description

Solution

01

Communication was cancelled by user's operation. -

02

Reception failed. The destination machine did not 
reply.

Contact the other party and have them check the 
status of their machine.

03

Communication was cancelled by user's operation. -

11

An error occurred while reading the document. 

Send again.

14

Memory is full. Fax was not received.

Check the following and increase the amount of 
available memory.
• Clear an out-of-paper error or a paper jam.
• Delete unnecessary images for Secure Receive.
• Print the documents received with the confidential 

reception.

• Delete the documents stored in the bulletin board 

box.

19

Delayed sending was cancelled by user's operation. -

21

Line error was detected.

Contact your dealer.

22

Transmission failed. The destination machine did 
not reply.

Check the following and send again.
If the error persists, contact your dealer.
• Check that you entered the correct fax number.
• Check that the dial type setting (Tone/Pulse) fits 

your phone line.

• The line may be busy. Wait a while and send 

again.

23

Redialed, but the destination machine did not reply. Check the following and send again.

If the error persists, contact your dealer.
• Check that you entered the correct fax number.
• Check that the dial type setting (Tone/Pulse) fits 

your phone line.

• The line may be busy. Wait a while and send 

again.

24

The telephone cable may be connected to the TEL 
connector by accident.

Connect the telephone cable to the LINE connector.

25

The telephone cable is not connected to the LINE 
connector.

Connect the telephone cable to the LINE connector.

Summary of Contents for MC573




























































































































































































































































































































































































































































































































Reviews:

No comments

Related manuals for MC573

Xerox D125 User Manual preview
D125
Brand: Xerox Pages: 310
Oki C610cdn Brochure & Specs preview
C610cdn
Brand: Oki Pages: 4
Canon Saddle Finisher-AF2 Service Manual preview
Saddle Finisher-AF2
Brand: Canon Pages: 244
Konica Minolta Bizhub 4020 Shortcut Manual preview
Bizhub 4020
Brand: Konica Minolta Pages: 40
Muratec MFX-3550 User Manual preview
MFX-3550
Brand: Muratec Pages: 213
Xerox ColorQube 87 Series Manual preview
ColorQube 87 Series
Brand: Xerox Pages: 32
Star Micronics TSP043E Series Hardware Manual preview
TSP043E Series
Brand: Star Micronics Pages: 24
Citizen CZ-01 User Manual preview
CZ-01
Brand: Citizen Pages: 32
U-Line ZEBRA ZD410 Manual preview
ZEBRA ZD410
Brand: U-Line Pages: 18
Kyocera Ecosys FS-C5300DN Operation Manual preview
Ecosys FS-C5300DN
Brand: Kyocera Pages: 35
Oki B411d Guide Utilisateur preview
B411d
Brand: Oki Pages: 157
Tektronix Phaser 220 Reference Manual preview
Phaser 220
Brand: Tektronix Pages: 178
Unytouch UPI3FL-80mm User Manual preview
UPI3FL-80mm
Brand: Unytouch Pages: 12
Jolimark NP311D Instruction Manual preview
NP311D
Brand: Jolimark Pages: 31
Unisys UDS2265+ Operator'S Manual preview
UDS2265+
Brand: Unisys Pages: 144
iDPRT SP410 User Manual preview
SP410
Brand: iDPRT Pages: 41
Oki Microline 182 Handbook preview
Microline 182
Brand: Oki Pages: 175
Xerox VersaLink C620 Installation Manual preview
VersaLink C620
Brand: Xerox Pages: 2

Brands by name

Popular brands

Load more brands