SHT-7540LPDN_rev031309
Model SHT-7540LPDN
SHT-7540LPDNP
TV System
NTSC PAL
Image Sensor
1/3” Sony Super HAD CCD II
DSP
Sony HQ-1
Total Pixels
811(H) x 508(V)
795(H) x 596(V)
Video Output
1.0Vp-p Composite / 75ohms
Resolution
540 TV Lines
Minimum
Illumination
0.08 Lux @ F1.0
Color mode automatically switches
to B/W mode under 2 Lux
Infrared
Sensitivity
700~1100nm
Electronic
Shutter Speed
AES ON, AES OFF, 1/100(120)sec,
FL:1/130sec,1/160sec,1/210sec,
1/280sec, 1/360sec, 1/420sec, 1/560sec
Back Light
Compensation
ON/OFF Switchable
Auto Gain
Control
ON/OFF Switchable
Day/Night
D/N / COLOR Switchable
DNR / Sens-up
High Gain/Low Noise Amplifier
Scan System
2:1 Interlace
Synchronization
Internal/Line Lock (AC Version Only)
S/N Ratio
More than 50dB (S.AGC OFF)
Auto Iris Control
Video / DC Switchable
Auto White
Balance
AWB
Lens Mount
CS/C (with adaptor)
Power
12V DC / 24V AC, 3.0W
90~260V AC, 4.5W
Operation
Temperature
14
o
F ~ 122
o
F / -10
o
C ~ 50
o
C
Storage
Humidity
RH 80% or less
Storage
Temperature
-4
o
F ~ 140
o
F / -20
o
C ~ 60
o
C
Dimension
4.72”(L) x 2.36”(W) x 1.97”(H)
120mm(L) x 60mm(W) x 50mm(H)
Weight
0.88 lbs / 400g
*Specifications are subject to change without notice
z
One (1) SHT-7540LPDN/SHT-7540LPDNP Camera
z
One (1) Operational Manual
* For any returns, please include all components listed above with
original packaging in Resalable Condition. Absolutely No Returns
will be accepted if any component is missing/damaged or if any cable is
cut or tampered with.
1. Never point the camera toward the sun
Do not expose the lens directly to the sun or to strong light as this
may damage the pick-up device.
2. Handle this camera with care
Avoid any shock or bumping of the camera. Improper handling
could damage the camera.
3. Requires a proper operating environment
This camera is designed for outdoor or indoor use. The allowable
temperature range for operation of this camera is between 14
°
F ~
122
°
F / -10
°
C ~ 50
°
C and the allowable humidity is 80%RH
maximum.
4. Clean the front face to the pick-up device
It is recommended that the pick-up device surface be cleaned
before lens installation or whenever the lens is changed.
Cleaning should be done by using a chamois, a very fine soft
cloth, lens tissue, or cotton tipped applicator and ethanol to
carefully remove any fingerprint or dust.
5. Check the power source voltage
The power source voltage should be within the specified range.
(Camera must meet the specifications). Camera must be
connected to a surge protector at all times.
6. Objects and liquid entry
Never push objects of any kind into this camera as this may
touch dangerous voltage points of short out parts that could
result in a fire or electric shock. Never spill any kind of liquid on
the video product.
7. Servicing
Do not attempt to service this video product by yourself as
opening or removing covers may expose you to dangerous
voltage or other hazards. Refer all service to qualified servicing
personnel.
8. Damage requiring service
Unplug this video product from the wall outlet and refer service
to qualified servicing personnel under the following conditions:
a. When the power supply cord or plug is damaged.
b. If liquid has been spilled, or objects have fallen into the
video product.
c. If the video product has been dropped or the cabinet has
been damaged.
d. When the video product exhibits a distinct change in
performance.
OKINA USA products are covered under warranty for one year from
the date of purchase. The warranty will automatically be voided if
any of the following occurs:
1. Camera sticker is removed
If the camera sticker is removed, we will not be able to confirm
any information regarding when and where the product was
purchased. We have no other way to verify the purchase record
without the serial number on the camera sticker; therefore, it
should not be removed.
2.
Camera is modified in any way
If the camera is scratched, damaged, or modified in a manner
not described in this manual, the warranty will be voided
immediately. It is the customer’s responsibility to keep the
camera in good condition.
3. Video or power cable is cut
The video cable and the power cable should not be tampered
with. Cutting or modifying of the cables will result in termination
of the warranty.
CAUTION
WARRANTY
SPECIFICATIONS
PACKAGE CONTENTS
