background image

5.2 Information and statistics in use for the unit 

The available information relevant to the use of the unit are:

 

Firmware

: SW version in use

 

Service

: last service carried out on the unit

 

Bottle

: capacity of internal bottle

 Hoses

: gas residual quantity in the hoses at the end of charging

 Press. switch

: pressure value; by reaching this value the recovery cycle is interrupted 

 Vacuum switch

: max pressure value before warning “system leakage” during the leak test cycle

 

Total recharges

: number of total carried out recharges 

 

Recovered fluid

: total quantity of recovered refrigerant 

 Recharged fluid: Total quantity of refrigerant charged into A/C systems 

 

Charged oil quantity: Total quantity of new oil t charged into A/C systems

 

Vacuum pump:

 using mode of vacuum pump

 

S/N:

serial number of the unit

6.Ordinary maintenance

The replacement of the filters and the oil of the vacuum pump has to be carried out by skilled personnel. It is
advisable that the maintenance service be followed by an authorized centre in order to make sure that the 
maintenance operations are carried out in a correct way so that the warranty of the product is not 
interrupted. The unit registers service operations in order to monitor the working hours of the filters and the 
vacuum pump oil , the software version installed in the unit and the data bank version (if available in your 
model) These counters have to be reset by the service personnel.

6.1 Filter replacement

Avoid the refrigerant to contaminate atmosphere.

Recover the gas residuals left in the charging hoses and in the filter 

Replace with original filters 

ATTENTION

! The filters have to be mounted according to the flow direction 

indicated by the arrow signed on the filters itself

6.2 Oil replacement of vacuum pump

1

Oil drain screw plug

2

Sight glass

3

Air inlet 

4

Oil filling cap

5

Exhaust fittings

6

Vacuum pump information plate

- Check the oil level by means of the relevant sight glass (2). The level of the oil (when the pump is not 
working) should be at the middle of the sight glass.

Ecos-150  sw  1.x.x  - ver. 1.0            

    

Page 18/20

Summary of Contents for ECOS-150





















Reviews: