background image

Maintenance operations have to be carried out by 

specialized and authorized personnel

.

Do not  

violate

 

for  any  reason at  all  

the safety devices  

the unit   is equipped with,  like the high

pressure valve of the internal reservoir.

Do not

 fill compressed air in the lines of the service unit or in the vehicle aircon system (a mixture of

air and refrigerant can be flammable or explosive); 

Please be aware that whatsoever damages due to a wrong or improper use of the recharging station will not
be covered by our warranty. Consumables like packing and seals for hoses and quick couplings, fuses and
damages occurred during transport are not part of the warranty.

1.2.1 Warning icons used in the present manual

Caution!

Connect to

230V socket

50Hz

Wear gloves

when handling

refrigerants

Wear goggles

when handling

refrigerants

Protect against

rain

Read

instruction

manual

carefully

1.2.2 Safety devices

A) Pressure release valves on internal gas tank:  releases pressure if 16 Bar are exceeded in the gas tank.

1.3 Scrapping of the unit

-

 Do not treat the unit as mixed solid waste for scrapping but take it to pieces ( waste separation).

- Refer to the specific collection points for waste of electric and electronic devices (AEE), according to the
relevant 

CEE RAEE 2002/95/EC, 2002/96/EC2003/108/EC

 regulation.

- The vacuum pump and the containers of new and used oil contain mineral and synthetic oil. Therefore the
specific  regulations  for   scrapping   have  to  be  followed.  The  same  procedure  has  to  be  followed  for  the
refrigerant gas residual in the storage bottle. The exhaust oil drained from the pump is a specific waste and
has to be collected according to the relevant regulations in force.

Ecos-150  sw  1.x.x  - ver. 1.0            

    

Page 4/20

Summary of Contents for ECOS-150





















Reviews: