24
OPERATION WITH DETERGENT
The Manufacturer recommends the use of detergents which are at least 90% biodegradable.
Refer to the label on the detergent for instructions on how to use it.
• Fill the bottle (34) with the desired detergent.
• Regulate the detergent suction capacity in the following way:
- disconnect the rod (33) from the lance (32);
- the
E
tooth on the rod (33) must match with one of the numbers on the inside of the lance (32) (1: minimum
suction; 6: maximum suction);
- re-connect the rod (33) in the lance (32).
• Insert the bottle (34) in the foam lance (32).
• Put the main switch (1) to position
“0”
and connect up the lance (32) and the spray gun (18).
• Start up the high pressure again, by putting the main switch (1) to position
“I”
and operating its lever (23)
(suction and mixing will start automatically when water goes through).
STOPPING THE CLEANER – TOTAL STOP MODE
• Release the cleaner gun lever (23) to stop the high pressure jet; the high pressure cleaner moves to the
by-pass operating mode and stops immediately.
• The cleaner will resume normal operation the as soon as the lever on the gun is pressed.
WARNING
• If you stop the high pressure jet and put the gun down, enable the locking handle (24).
Step C in Fig. 5.
STOPPING
• Run the cleaner for a few minutes with cold water.
• Close the tap on the water supply off completely (or remove the suction pipe from the draft tank).
• Drain the water out of the cleaner by running it for a few seconds with the cleaner gun lever (23) pressed.
• Move the master switch (1) to
“0”
• Take the plug out of the power socket.
• Eliminate any remaining pressure in the high pressure hose (26) by keeping the cleaner gun lever (23)
pressed down for a few seconds.
• Wait for the cleaner to cool down.
STORAGE
• Wind up the high pressure hose (26) with due care, making sure it is not bent; store it carefully, without
damaging it.
• Wind up the power cord (6) carefully its support (7).
• Store the high pressure cleaner in a clean, dry place. Make sure the power cord and the high pressure
hose are not damaged.
Summary of Contents for IP 2500 HS
