32
• En cas de manque ou d’insuffisance de gasoil, le brûleur s’arrête.
• Le brûleur commence à fonctionner après environ trois secondes à partir de l’ouverture du pistolet haute
pression et arrête son fonctionnement lorsqu’on ferme le pistolet haute pression ou lorsque la température
maximale admissible a été atteinte.
• Pour passer l’appareil du fonctionnement à l’eau chaude au fonctionnement à l’eau froide, tourner l’
’interrupteur eau chaude (31) en position
“0”
.
FONCTIONNEMENT AVEC DÉTERGENT
Les détergents recommandés par le fabricant sont biodégradables à plus de 90%.
Pour l’utilisation du détergent, consulter l’étiquette apposée sur l’emballage du produit.
• Remplir le flacon (34) avec le détergent désiré.
• Régler la capacité d’aspiration du détergent de la façon suivante :
- extraire la tige (33) de la lance (32) ;
- faire correspondre la dent
E
de la tige (33) avec un des numéros figurant à l’intérieur de la lance (32)
(1 : aspiration minimale ; 6 : aspiration maximale) ;
- réintroduire la tige (33) dans la lance (32).
• Introduire le flacon (34) dans la lance agent moussant (32).
• Mettre l’interrupteur général (1) sur
« 0 »
et raccorder la lance (32) au pistolet haute pression (18).
• Redémarrer le nettoyeur haute pression, en mettant l’interrupteur général (1) sur
« I »
et actionner la
gâchette (23) (l’aspiration et le mélange ont lieu automatiquement au passage de l’eau).
INTERRUPTION DU FONCTIONNEMENT – TOTAL STOP
• En relâchant la gâchette (23) du pistolet haute pression, on arrête le jet haute pression et le nettoyeur
haute pression passe en fonctionnement de by-pass et s’arrête automatiquement.
• Le nettoyeur haute pression se remet à fonctionner normalement dès que l’opérateur appuie à nouveau
sur la poignée du pistolet haute pression.
ATTENTION
• Si l’on doit stopper le fonctionnement du jet haute pression et poser le pistolet haute pression, il faut insérer
le bouton de blocage (24) de la poignée de celui-ci.
Opération
C
Fig.
5.
ARRÊT
• Faire fonctionner le nettoyeur haute pression pendant quelques minutes à l’eau froide.
• Former totalement le robinet de l’eau (ou sortir le tuyau d’aspiration du réservoir d’aspiration).
• Faire fonctionner le nettoyeur haute pression en gardant enfoncée la gâchette (23) du pistolet haute
pression pendant quelques secondes pour le vidanger.
• Mettre l’interrupteur général (1) en position
« 0 »
.
• Débrancher la fiche électrique de la prise de courant.
• Garder enfoncée la gâchette (23) du pistolet haute pression pendant quelques secondes pour éliminer
l’éventuelle pression résiduelle dans le tuyau haute pression (26).
• Attendre que le nettoyeur haute pression se refroidisse.
MISE AU REPOS
• Enrouler le tuyau haute pression (26) avec soin en évitant de le plier ; pendre le tuyau à son support sans
l’endommager.
• Enrouler le câble électrique (6) avec soin et le pendre à son support (7).
• Mettre le nettoyeur haute pression dans un endroit sec et propre en veillant à n’endommager ni le câble
électrique ni le tuyau haute pression.
Summary of Contents for IP 2500 HS
