112
PROBLÈMES AVEC LE PLATEAU DE COUPE
PROBLÈME
CAUSES POSSIBLES
SOLUTION
LE PLATEAU DE
COUPE NE TOND
PAS DE FAÇON
HOMOGÈNE
Herbe et saletés accumulées
à l'intérieur du plateau de coupe
►
Retirez l'herbe sous le plateau de coupe.
Lames émoussées ou déformées
►
Vérifiez l'état des lames et affûtez-les ou remplacez-
les si nécessaire (
6.3.6
)
Axe de lame endommagé ou usé
►
Vérifiez l'état de l'axe.
Une courroie ou les deux sont
insuffisamment tendues
►
Vérifiez la tension et retendez si nécessaire
(
6.3.8 and 6.3.9
).
UNE BANDE RESTE
NON TONDUE ENTRE
LES ROTORS DE LAME
Lames émoussées ou déformées
►
Vérifiez l'état des lames et affûtez-les ou remplacez-
les si nécessaire (
6.3.6
)
Carter de roulement endommagé
►
Vérifiez l'état des roulements et effectuez en fonction
du résultat une réparation ou un remplacement.
Quand l’herbe à couper est épaisse ou trop humide,
une bande d'herbe peut rester intacte. La vitesse
de déplacement doit être ajustée pour respecter
les conditions de coupe en passant à une vitesse
appropriée. Le moteur ne doit pas fonctionner avec la
vanne de l'accélérateur complètement ouverte.
LE PLATEAU DE
COUPE DÉCHIQUÈTE
LE GAZON
Lames tordues
►
Vérifiez
l'état
des
lames
et
affûtez-
les
ou
remplacez-les
si
nécessaire
(
6.3.6
)
Carter de roulement endommagé
►
Vérifiez l'état des roulements et effectuez en fonction
du résultat une réparation ou un remplacement.
La courroie d'entraînement n'est pas
suffisamment tendue
►
Vérifiez la tension de la courroie d'entraînement
(
6.3.8 et 6.3.9
) et tendez-la à nouveau si besoin.
Hauteur de tonte inappropriée
►
Vérifiez la hauteur de tonte et réglez-la si nécessaire.
Le gazon est plus fréquemment déchiqueté sur les
terrains irréguliers.
LE PLATEAU DE
COUPE N'ÉJECTE PAS
L'HERBE
Herbe accumulée à l'intérieur du
plateau de coupe
►
Retirez l'herbe sous le plateau de coupe. Par temps
humide, la goulotte d’éjection et la partie inférieure de
la sortie du plateau de coupe peuvent s’obstruer avec
l'herbe. Ne tondez pas de l'herbe mouillée.
La courroie d'entraînement n'est pas
suffisamment tendue
►
Vérifiez la tension de la courroie d'entraînement
(
6.3.8 et 6.3.9
) et tendez-la à nouveau si besoin.
Vitesse de déplacement inappropriée
►
Réglez la vitesse de déplacement conformément aux
conditions de tonte. Le moteur ne doit pas fonctionner
avec la soupape d’étranglement complètement
ouverte. Lorsque vous tondez de l'herbe haute, tondez
d'abord à une hauteur élevée puis une nouvelle fois
à une hauteur normale. Respectez les informations du
chapitre
5.5.3
.
Lame mal installée
►
Vérifiez que les lames sont installées correctement,
notamment après leur remplacement.
Summary of Contents for OM 105J
