201
Quando le lame impattano contro un ostacolo solido, è necessario fermare immediatamente il motore e controllarle! I perni
di sicurezza potrebbero essere danneggiati o rotti.
Quando si manipolano le lame, indossare guanti da lavoro spessi.
Utilizzare esclusivamente lame consigliate dal produttore o dal fornitore del trattorino tosaerba. L'uso di lame e/o parti di
fissaggio non consigliate potrebbe produrre risultati di taglio non adeguati, danni al trattorino tosaerba e anche lesioni
personali qualora le lame dovessero staccarsi durante il funzionamento.
6.3.7 PIATTO TAGLIAERBA - ISPEZIONE ED EQUILIBRATURA
Per ottenere risultati di taglio ottimali, il piatto tagliaerba deve essere impostato all'altezza di taglio corretta ed entrambi i lati del
piatto tagliaerba devono essere in piano.
Prima di eseguire la regolazione:
►
Posizionare il trattorino tosaerba su una
superficie il più possibile uniforme
,
gonfiare tutti i pneumatici alla pressione
indicata
(80 - 140 kPa, differenza di ±10 kPa tra i singoli pneumatici) e
bloccare l'intero tosaerba per evitare qualsiasi
movimento
(ad esempio, utilizzando un apposito cuneo, ecc.).
►
Portare la leva di regolazione dell'altezza del piatto tagliaerba in posizione
1
.
Il piatto tagliaerba è dotato di coperture in plastica che impediscono alle mani di accedere alle parti in movimento e ai
componenti di trazione del trattorino tosaerba.
I coperchi possono essere rapidamente e facilmente rimossi utilizzando i perni di attacco rapido ai lati. Infilare un
cacciavite nella scanalatura del perno e ruotare in senso antiorario. Quindi togliere il coperchio dal trattorino tosaerba.
6.3.7a
Macchine 106, 106 4x4 , 124:
►
La distanza
A
è l'estremità anteriore del piatto tagliaerba nella direzione di marcia e deve essere a
23-25 mm
da
terra. Controllare entrambi i lati del piatto tagliaerba. Se c'è differenza di altezza, allentare i controdadi (
2
) sulla
rispettiva barra di trazione (
1
) e regolare l'altezza girando i dadi (
3
). Dopo aver impostato l'altezza corretta, non
dimenticare di serrare nuovamente i controdadi (
2
).
►
La distanza
B
è l'estremità posteriore del piatto tagliaerba nella direzione di marcia e deve essere a
28-30 mm
da
terra, ovvero l'estremità posteriore deve essere più in alto di almeno 5 mm rispetto all'estremità anteriore. Se c'è
differenza di altezza, regolarla allentando i dadi (
4
), regolando il bordo all'altezza corretta e serrando i dadi a una
coppia di
55 – 65 Nm
.
6.3.7b
Macchine 110:
►
La distanza
A
è l'estremità anteriore del piatto tagliaerba nella direzione di marcia e deve essere a
30-34 mm
da
terra. Controllare entrambi i lati del piatto tagliaerba. Se c'è differenza di altezza, allentare i controdadi (
2
) sulla
rispettiva barra di trazione (
1
) e regolare l'altezza girando i dadi (
3
). Dopo aver impostato l'altezza corretta, non
dimenticare di serrare nuovamente i controdadi (
2
).
►
La distanza
B
è l'estremità posteriore del piatto tagliaerba nella direzione di marcia e deve essere a
28-30 mm
da
terra, ovvero l'estremità posteriore deve essere più in alto di almeno 5 mm rispetto all'estremità anteriore. Se c'è
differenza di altezza, regolarla allentando i dadi (
4
), regolando il bordo all'altezza corretta e serrando i dadi a una
coppia di
55 – 65 Nm
.
Se non si è sicuri in merito a questa procedura, farla eseguire presso un centro di assistenza.
6.3.8 PIATTO TAGLIAERBA - ISPEZIONE E REGOLAZIONE DELLA CINGHIA TRAPEZOIDALE
6.3.8a
6.3.8b
Per via dei carichi cui è sottoposta, la tensione della cinghia di trasmissione del piatto tagliaerba (
1
) si riduce con il
tempo, rendendo necessario un tensionamento. La cinghia viene tesa tramite bulloni e una molla.
►
Impostare il piatto tagliaerba nella posizione 1.
►
Utilizzando una chiave adatta, girare il dado (
2
) in modo tale che la molla (
3
) risulti tesa a un valore di:
Macchine 106, 106 4x4:
145±1 mm.
Macchina 110:
150±1 mm.
Macchina 124:
155±1 mm.
6.3.9 PIATTO TAGLIAERBA - REGOLAZIONE DELLA CINGHIA DENTATA DI TRASMISSIONE DELLE LAME
Macchine 106, 106 4x4 , 124:
6.3.9a
►
Abbassare il piatto tagliaerba portando la leva di regolazione dell'altezza in posizione
1
.
►
Rilasciare i perni di attacco rapido dei coperchi laterali del piatto tagliaerba e rimuovere i coperchi.
►
Rilasciare il perno di attacco rapido (
1
) del coperchio superiore (
2
) e, circa a metà, inclinare il coperchio verso l'alto.
6.3.9b
►
Far scorrere una chiave appropriata sotto la copertura di metallo; da sotto, posizionarla sul bullone della puleggia
della cinghia (
1
). Da sopra, allentare il dado della puleggia della cinghia.
►
Allentare il controdado (
2
) e il dado (
3
). Quindi, utilizzando una chiave appropriata, girare il dado (
3
) in modo che la
cinghia dentata (
4
) sia ben tesa.
Summary of Contents for OM 105J
