207
PROBLEMI AL PIATTO TAGLIAERBA
PROBLEMA
POSSIBILI CAUSE
SOLUZIONE
IL PIATTO
TAGLIAERBA NON
TAGLIA IN MODO
UNIFORME
Erba e detriti accumulati all'interno del
piatto tagliaerba
►
Rimuovere i detriti da sotto il piatto tagliaerba.
Lame smussate o deformate
►
Verificare lo stato delle lame e affilare o sostituire
secondo necessità (
6.3.6
)
Albero delle lame danneggiato
o usurato
►
Verificare lo stato dell'albero.
Una o entrambe le cinghie non sono
tese a sufficienza
►
Controllare la tensione e tendere se necessario
(
6.3.8 e 6.3.9
).
RIMANE UNA STRISCIA
NON TAGLIATA TRA
I ROTORI DELLE LAME
Lame smussate o deformate
►
Verificare lo stato delle lame e affilare o sostituire
secondo necessità (
6.3.6
)
Alloggiamento del cuscinetto
danneggiato
►
Verificare lo stato dei cuscinetti e, in base ai risultati,
eseguire una riparazione o la sostituzione. Quando
si taglia erba spessa o eccessivamente umida, è
possibile che resti una striscia non tagliata. La velocità
di avanzamento deve essere adattata alle condizioni di
taglio selezionando una marcia corretta. Il motore deve
funzionare con la valvola a farfalla completamente
aperta.
IL PIATTO
TAGLIAERBA STA
SRADICANDO IL
MANTO ERBOSO
Lame piegate
►
Verificare lo stato delle lame e affilare
o
sostituire
secondo
necessità
(
6.3.6
)
Alloggiamento del cuscinetto
danneggiato
►
Verificare lo stato dei cuscinetti e, in base ai risultati,
eseguire una riparazione o la sostituzione.
La cinghia di trasmissione non è
sufficientemente tesa
►
Controllare la tensione della cinghia di trasmissione
(
6.3.8 e 6.3.9
) e tenderla se necessario.
Altezza di taglio inadeguata
►
Controllare l'altezza di taglio e, se necessario,
regolarla. Il manto erboso viene danneggiato più di
frequente su terreni irregolari.
IL PIATTO
TAGLIAERBA NON
ESPELLE L'ERBA
Si è accumulata erba all'interno del
piatto tagliaerba
►
Rimuovere l'erba da sotto il piatto tagliaerba. In
condizioni di bagnato, lo scivolo di scarico e la parte
inferiore del piatto tagliaerba potrebbero intasarsi
d'erba. Non tagliare erba bagnata.
La cinghia di trasmissione non è
sufficientemente tesa
►
Controllare la tensione della cinghia di trasmissione (
6.3.8 e 6.3.9
) e tenderla se necessario.
Velocità di marcia inadeguata
►
Adeguare la velocità di marcia alle condizioni di taglio.
Il motore deve funzionare con la valvola a farfalla
completamente aperta. Quando si taglia erba alta,
eseguire un primo passaggio con altezza di taglio
maggiore, poi un secondo passaggio ad altezza
normale. Seguire le informazioni contenute nel
capitolo
5.5.3.
Lama non installata correttamente
►
Verificare, in particolare dopo aver sostituito le lame,
che la lama sia installata correttamente.
Summary of Contents for OM 105J
