297
► Compruebe que las cuchillas estén equilibradas, véase más arriba.
►
Atornille las nuevas cuchillas. Durante la instalación, asegúrese de que la curva de las cuchillas mire hacia arriba, hacia el cuerpo de
la plataforma de corte. No intercambie las cuchillas izquierda y derecha. La cuchilla derecha tiene un perno con rosca a la izquierda.
► Utilizando una llave dinamométrica, apriete con cuidado los pernos de fijación al par de apriete especificado de
30
±
3 Nm
.
Este par de apriete se consigue cuando el muelle tangencial (convexo) de debajo del perno de fijación está completamente
comprimido y, desde este punto en adelante, el perno no se aprieta.
Sin las cuchillas impactan con un obstáculo macizo, detenga de inmediato el motor y compruebe las cuchillas. Los
pasadores de seguridad podrían haberse dañado o roto.
Cuando manipule las cuchillas de corte, utilice siempre guantes de protección para trabajos pesados.
Utilice siempre cuchillas recomendadas por el fabricante o el proveedor del tractor cortacésped. El uso de cuchillas y
piezas de fijación no recomendadas podría causar resultados inadecuados de corte, daños en el cortacésped y, en caso de
desprendimiento durante el funcionamiento, lesiones personales.
6.3.7 PLATAFORMA DE CORTE: INSPECCIÓN Y EQUILIBRADO
Para obtener los mejores resultados, la plataforma de corte debe estar ajustada a la altura de corte correcta y ambos lados de la
plataforma tienen que estar nivelados.
Antes de efectuar el ajuste:
► Coloque el cortacésped en una
superficie totalmente uniforme
,
hinche todos los neumáticos con la presión indicada
(80-
140 kPa, ±10 kPa de diferencia entre cada neumático) e inmovilice todo el cortacésped
para que no se pueda mover
(p. ej. con
una cuña adecuada, etc.).
►
Mueva la palanca de ajuste de la altura de la plataforma de corte a la posición
1
.
La plataforma de corte está equipada con cubiertas de plástico que impiden que se puedan acercar las manos a las
piezas móviles y a las piezas de accionamiento del cortacésped.
Estas cubiertas se pueden desmontar rápida y fácilmente mediante los pasadores de acoplamiento rápido que tienen
a los lados. Introduzca un destornillador en la ranura del pasador y gírelo en sentido antihorario. A continuación, extraiga
la cubierta del cortacésped.
6.3.7a
Máquinas 106, 106 4x4 , 124:
►
La distancia
A
es el borde delantero de la plataforma de corte en la dirección de desplazamiento y debe ser de
23-25 mm
por encima del suelo. Compruébela en ambos lados de la plataforma de corte. Si la altura es diferente,
afloje las tuercas de fijación (
2
) de la varilla de tracción correspondiente (
1
) y ajuste la altura girando las tuercas (3).
Después de ajustar la altura al valor correcto, acuérdese de apretar las tuercas de fijación (
2
).
►
La distancia
B
es el borde trasero de la plataforma de corte en la dirección de desplazamiento y debe ser de
28-
30 mm
por encima del suelo; es decir, el borde trasero debe estar al menos 5 mm por encima del borde delantero.
Si la altura es diferente, ajústela de la siguiente manera: afloje las tuercas (
4
), ajuste el borde a la altura correcta y
apriete las tuercas a un par de 55–65 Nm.
6.3.7b
Máquinas 110:
►
La distancia
A
es el borde delantero de la plataforma de corte en la dirección de desplazamiento y debe ser de
30-34 mm
por encima del suelo. Compruébela en ambos lados de la plataforma de corte. Si la altura es diferente,
afloje las tuercas de fijación (
2
) de la varilla de tracción correspondiente (
1
) y ajuste la altura girando las tuercas (3).
Después de ajustar la altura al valor correcto, acuérdese de apretar las tuercas de fijación (
2
).
►
La distancia
B
es el borde trasero de la plataforma de corte en la dirección de desplazamiento y debe ser de
28-
30 mm
por encima del suelo; es decir, el borde trasero debe estar al menos 5 mm por encima del borde delantero.
Si la altura es diferente, ajústela de la siguiente manera: afloje las tuercas (
4
), ajuste el borde a la altura correcta y
apriete las tuercas a un par de 55–65 Nm.
Si no se siente suficientemente seguro como para hacer este procedimiento, encárguelo a un centro de servicio técnico.
6.3.8 PLATAFORMA DE CORTE: COMPROBACIÓN Y AJUSTE DE LA CORREA TRAPEZOIDAL
6.3.8a
6.3.8b
Debido a la exigencia a que está sometida, la correa de accionamiento de la plataforma de corte (
1
) pierde tensión con
el tiempo y es necesario volver a tensarla. La correa se tensa utilizando pernos y un muelle.
►
Ajuste la plataforma de corte a la posición 1.
►
Utilizando una llave adecuada, gire la tuerca (
2
) de forma que el muelle (
3
) se tense hasta un valor de:
Máquinas 106, 106 4x4:
145±1 mm.
Máquina 110:
150±1 mm.
Máquina 124:
155±1 mm.
6.3.9 PLATAFORMA DE CORTE: AJUSTE DE LA CORREA DENTADA DE ACCIONAMIENTO DE LAS CUCHILLAS
Máquinas 106, 106 4x4 , 124:
Summary of Contents for OM 105J
