300
6.3.17 RESUMEN DEL PAR DE APRIETE DE LAS UNIONES ATORNILLADAS
Plataforma de corte:
Par
Perno central de la cuchilla
30
±
3 Nm
Tuercas M12 de las poleas del accionamiento de corte
45 - 55 Nm
Perno 10x25 KL 100 RIPP del brazo de la polea de tensión de la correa de accionamiento de corte
55 - 65 Nm
Dirección:
Perno M8x30 del segmento de la dirección
15 - 25 Nm
Tuerca M12 del segmento de la dirección
35 - 45 Nm
Motor:
Perno del embrague electromagnético
60 - 70 Nm
Perno del soporte de la polea de la correa de desplazamiento
25 - 35 Nm
Una vez extraídas, las tuercas de fijación se deben sustituir por otras nuevas.
6.4 LUBRICACIÓN
Lubrique el cortacésped conforme a la imagen 6.4 y la tabla de abajo. Si el cortacésped se utiliza en lugares con mucho polvo
o tierra, lubríquelo más a menudo.
Los rodamientos de bolas de las poleas de tensado, las poleas guía y los rodamientos de la plataforma de corte son autolubricantes.
Antes de empezar a lubricar, el motor debe estar apagado y todas las piezas móviles del cortacésped deben estar quietas.
6.4
Símbolo
Explicación
Actividad
Lubricante para plástico A00
---
Aceite SAE 30
---
50
Intervalo en horas
---
(1)
Pasador central rotativo del cárter del eje
Lubricar con una aceitera
(2)
Rodamientos de ambas ruedas delanteras y pasadores del cárter del eje
Lubricar con una aceitera
(3)
Unión angular de las varillas de tracción de la dirección
Retirar y lubricar
(4)
Puntos de rotación de los pedales en ambos lados del cortacésped
Lubricar sin retirar
(5)
Perno de la varilla de tracción de elevación de la plataforma de corte
Lubricar sin retirar
(6)
Semiejes de las ruedas traseras (transmisiones)
Retirar la rueda y lubricar
(7)
Bandeja de la varilla de tracción de la dirección
Lubricar sin retirar
(8)
Puntos de rotación del mecanismo de elevación de la plataforma de corte
Lubricar sin retirar
(9)
Segmento dentado de la dirección, excéntrica y unión angular de la varilla
de tracción de la dirección
Lubricar sin retirar
(10)
Pasador de la rueda delantera
Lubricar con una aceitera
(11)
Unión angular de las varillas de tracción de la dirección
Retirar y lubricar
No permita que el aceite y los lubricantes entren en contacto con las correas de accionamiento y sus poleas. Limpie bien con un paño
el área alrededor de las piezas lubricadas, tanto antes como después de la lubricación.
Antes de poner fuera de servicio el cortacésped durante un periodo largo de tiempo, lubrique bien todos los puntos que se indican en
la imagen
,
especialmente los semiejes delanteros y traseros.
Summary of Contents for OM 105J
