334
5
PRACA I OBSŁUGA MASZYNY
Informacje, z którymi należy się zapoznać przed pierwszym uruchomieniem kosiarki samojezdnej:
► Kosiarka samojezdna wyposażona jest w zabezpieczające styki, które załączane są przez:
- przełącznik umieszczony pod siedzeniem
- przełącznik założenia kosza na trawę, ewentualnie deflektora
- przełącznik napełnienia kosza na trawę
- przełącznik pedału hamulca
► Silnik automatycznie się zatrzyma, kiedy kierowca opuści siedzenie i maszyna nie jest zahamowana hamulcem
postojowym.
► Silnik można włączyć tylko wtedy, gdy kosiarka samojezdna jest wyłączona, a kosz na trawę jest podłączony, lub
gdy deflektor, który podczas ściółkowania zapobiega wpadaniu ściętej trawy do wyrzutnika prowadzącego do kosza
na trawę, jest podłączony i wciśnięty jest pedał hamulca.
5.1
KONTROLE PRZED URUCHOMIENIEM MASZYNY
Przed uruchomieniem kosiarki samojezdnej trzeba skontrolować następujące:
►
Poziom oleju w silniku (
3.4.1
)
►
Stan akumulatora (
3.4.2
)
►
Poziom paliwa (
3.4.3
)
► Ciśnienie powietrza w oponach (
3.4.4
)
► Czy dźwignia odłączania znajduje się w pozycji „
1
”
5.2
URUCHAMIANIE SILNIKA
Maszyna wyposażona jest w system blokowania startu silnika, o ile nie są spełnione następujące warunki:
Napęd mechanizmu tnącego jest odłączony
Pedał jazdy nie jest wciśnięty
Kierowca siedzi na siedzeniu maszyny
Pedał hamulca jest wciśnięty lub hamulec jest włączony w położeniu postojowym
STOP
OK
NO OK
P
(
(
)
)
P
(
(
)
)
O spełnieniu
tych wymogów w momencie uruchamiania silnika informuje
czerwona kontrolka pedału hamulca oraz kontrolka pedału postojowego
świecące stałym światłem na czerwono
STOP
OK
NO OK
P
(
(
)
)
P
(
(
)
)
.
Czerwona kontrolka pełni również funkcję kontrolki stanu akumulatora!
Jeśli czerwona kontrolka zacznie świecić przerywanie (migać), i choć pedał
hamulca nie jest wciśnięty i stacyjka jest ustawiona w położenie „zapłon
włączony.”, oznacza to niski poziom naładowania akumulatora. Jeżeli
dojdzie do zapalenia kontrolki przerywanym świeceniem podczas pracy,
nie działa poprawnie ładowanie akumulatora. W takim przypadku należy jak
najszybciej skontaktować się z autoryzowanym serwisem.
O niespełnieniu
tych wymogów w momencie uruchamiania silnika informuje
czerwona kontrolka pedału hamulca oraz kontrolka pedału postojowego
świecące światłem przerywanym
(migające)
STOP
OK
NO OK
P
(
(
)
)
P
(
(
)
)
.
Po spełnieniu opisanych wymogów, należy uruchomić silnik zgodnie z opisem poniżej:
1) Nacisnąć pedał hamulca.
2) Ustawić dźwignię ustawiania podniesienia mechanizmu tnącego w pozycji
„7”
.
3) Dźwignię przepustnicy należy ustawić następująco:
- W maszynach z silnikiem dwucylindrowym na położenie
“MAX
”
- W maszynach z silnikiem jednocylindrowym na położenie
“SSANIE
”
4) Wyciągnąć przełącznik ssania
(tylko w maszynach wyposażonych w samodzielne ssanie)
5) Przekręcić stacyjkę w położenie „Zapłon włączony” i poczekać co najmniej 1 sekundę. W tym czasie przeprowadzona zostanie
diagnostyka systemu elektronicznego maszyny. Następnie przekręcić stacyjkę w położenie „Uruchomienie silnika”, co spowoduje
rozruch silnika. Po uruchomieniu silnika należy puścić kluczyk, stacyjka automatycznie powróci do położenia „Zapłon włączony”.
Summary of Contents for OM 105J
